The tag has no wiki summary.

learn more… | top users | synonyms

1
vote
2answers
135 views

Compound mortise and tenon joints on corners (ie. legs of a table)

I am playing around with the idea of doing a workbench that can be disassembled, using pinned mortise and tenon joints. I haven't found anything that could be used where two spans meet at a corner ...
5
votes
3answers
8k views

How should I level (flatten) ceiling joists for drywall?

My kitchen ceiling joists are old and at varying heights. I'm trying to make it level, or at least flat, in preparation for drywall installation. Would you suggest installing strips of wood to the ...
1
vote
1answer
111 views

How can I create a polycarbonate roof valley?

My roof valley is wider than this. I want light to pass in through. Is the polycarbonate I should use? Can I make a joint somewhere in the middle through the length with polycarbonate. I need some ...
3
votes
3answers
910 views

What advantages does bending copper pipes have over joining many parts without brazing?

These questions are in context of a DIY solar water heater I am planning (another separate question). The copper pipes in question, are supposed to carry around hot water using thermo-siphon ...
4
votes
2answers
2k views

Can blue (lightweight) drywall compound be used for all coats?

I had a guy come in to do some drywall taping today and I had a bag of 20 min hot mud and a bucket of each green (regular) and blue (lightweight) joint compound. I always though that the green should ...
3
votes
2answers
4k views

How do I transition between tile and drywall in a tub surround?

I'm working on a tub surround, which is about to be tiled. And the last piece I need to figure out, is how to transition between finished tile and adjacent wall. This is how my wall looks right now. ...
2
votes
2answers
436 views

Which technique of wood joining is the best for joining these boards of a small table?

I want to join these four 1.8 cm thick beechwood boards as one can see on the picture. My idea is to join at the B points with biscuits but I’m not sure what to do about the A points. It needs to be a ...
8
votes
5answers
6k views

What can I use to drill dowel holes down the end of a long piece of wood?

More of a DIY than Improvement question, but here goes anyway. We're building a shoe box with slatted sides and base and were thinking of joining the slats to the corner uprights with dowel (excuse ...
2
votes
3answers
428 views

How to make a Bevel Lap Splice joint, for connecting a portable floor?

I'm new to woodworking, and I've read that I could potentially create this joint using a table saw, jointer, or even a circular saw - but I do not want to rent/purchase one and find out that I can't. ...
3
votes
4answers
2k views

Dado (+glue) or just screws (+glue) for painted MDF bookcase

I am thinking of building some MDF build-in bookcases, dado joints are clearly stronger but creates lots of mess from a router and takes more time. As the book case will be painted, I can hide any ...
4
votes
2answers
805 views

Did I just ruin the flange on our toilet?

The point where the elbow joint from our flushometer meets the toilet bowl has begun leaking (dripping, really) whenever we flush (so, whenever water passes through it). I jiggled it a bit and the ...
4
votes
1answer
876 views

What kind of connection is used to attach the legs to this table?

I (a beginner) would like to build a table of this form. Does anyone know what kind of corners are used to connect the legs, or any other construction tips.
5
votes
1answer
5k views

How can I join 2x6 pressure treated wood for a shed base?

I am creating a wood frame for my Suncast Sierra shed. I already weighed the pros and cons of each option for a base and came out with a wood frame as the most economical with all factors considered. ...
8
votes
2answers
800 views

How do I drill a mortise and tenon joint so I can reinforce it with a dowel?

I want to make a mortise and tenon joint that will be held together with a dowel instead of glue. How can I drill the hole in the mortised stock and the tenon so that they line up accurately and ...
4
votes
1answer
393 views

When should I round over the edges leading to a miter joint?

I'm going to be joining 2 1x6" pieces of wood at a simple miter joint. However, I want the top edges to be rounded over. I'm planning to use my router and a round over bit to soften the edges, the ...
9
votes
2answers
7k views

How can I level my basement floor, which has a 4-inch dip?

I googled today on how to level a basement floor. Most people recommend using SLC (self leveling concrete)... I don't think I can just use that because of the pitch of my floor (and from what I hear, ...
5
votes
1answer
177 views

How can I extend existing 8 x 8 pilings?

I am converting a deck to a boat lift. I have 8x8 sqaure pilings built at deck height, 2.5 ft above water. I knew it might get converted into a boat lift so they are all in the correct location. But ...
5
votes
2answers
2k views

Drywall - final joint compound coat

While remodeling an older house (where nothing is quite straight) we used fiber glass mesh joint tape and 3 coats of joint compound. The first coat was applied with a 4 inch knife, the second with an ...
6
votes
1answer
683 views

Paper joint tape VS. Mesh joint tape

What are the pros and cons of each type of drywall joint tape? Are there situations where one should always be used over the other?
1
vote
1answer
335 views

60 degree corner molding

I have a corner joint I need hidden, for which I'd normally use a quarter round molding, but because this is part of a cathedral ceiling, the angle is much narrower than 90 degrees, it's 60 degrees. ...
1
vote
1answer
94 views

Home-made joint for a top window

I have some sort of artisanal, metal, top oriented, window that essentially serves as a light well (but the room is almost completey dark, the main door is covered by a curtain because my girl friend ...