Ground fault circuit interrupter, also referred to GFCI, GFI, or a residual-current device. This devices detects a leak in current, or an imbalance between the current on the hot and neutral wires. This is used to prevent electrical shock.

learn more… | top users | synonyms

17
votes
7answers
109k views

How do I install a GFCI receptacle with two hot wires and common neutral?

In my kitchen, I want to replace a regular 120V receptacle with a GFCI-protected receptacle. The instructions describe what to do with a regular 2-wire + ground feed, with and without daisy chaining ...
6
votes
1answer
35k views

How do I wire a GFCI/Switch Combo?

I'm replacing an old GFCI/Switch combo. In the old one there are two wires coming into the line side, a hot wire and a neutral. On the load side there is one wire leading up to the lighting fixture. ...
10
votes
1answer
24k views

Can I add a standard receptacle on a GFCI circuit

So, I want to add a receptacle in the bathroom (I tend to run out of batteries on my phone while crapping at the end of the day). There's a GFCI outlet on the other side of the crapper wall that ...
14
votes
4answers
63k views

Which Kitchen outlets do NOT need GFCI?

I have the 2 circuits in the kitchen with GFCI outlets, but I'm not quite sure which other ones do NOT need GFCI. Other circuits in the kitchen include Microwave, Fridge, and Dishwasher. It makes ...
13
votes
4answers
39k views

When to use holes instead of side terminals to wire an outlet

This question comes from Shirlock's comment on this GFCI wiring question. When and why should you use the holes on the back of an outlet rather than the side terminals? I always assumed the holes on ...
5
votes
4answers
14k views

Why does my circuit breaker trip with any small load, even after replacing the breaker?

I have a 20A 240V GFCI breaker in my main breaker box going to a conduit to another breaker box outside. All worked well last summer. Now, when I put any load (weed-eater, light, etc.) on an outlet ...
3
votes
3answers
305 views

Does a GFCI receptacle provide overcurrent protection?

Does a GFCI receptacle provide over-current protection? (note that I'm not referring to GFCI circuit breakers as may be found in a service panel, nor to specialty devices such as an inline plug-in ...
10
votes
2answers
8k views

How should I address my bathroom's flickering lights and GFCI tripping mysteriously? (Schematic included.)

So I inherited a bit of a nightmare for wiring in my bathroom. I'll be calling in an electrician, but wanted to have an understanding of the problem first, as not to be ripped off, lead astray, etc.. ...
5
votes
4answers
7k views

Should I use a GFCI or AFCI circuit breaker with knob and tube wiring?

My American house was built in 1942, and much of the wiring is still knob-and-tube wiring (2-wire, no ground). Over the years new modern wiring has been added to the house, but we still have some KnT ...
3
votes
1answer
1k views

When replacing non-grounding type receptacles is a GFCI receptacle required, or can any GFCI device be used?

Under the NEC (it was 210(7)(d)(3), but appears to have moved around some), it is permissible to replace an ungrounded receptacle with a GFCI receptacle, then wire further ungrounded or non-grounded (...
6
votes
1answer
18k views

How should I wire a GFCI outlet and a switch to isolate the switch but provide GFCI protection further in the series?

I am replacing the outlets for my garbage disposal/dishwasher circuit in my kitchen. Currently on that breaker there is one non-GFCI outlet with a pigtailed switch controlling the garbage disposal and ...
1
vote
4answers
12k views

How do I wire a GFCI combination light switch when power enters at the light?

I have a Leviton 7299-NW GFCI/switch combo The diagrams in a response to the question "How do I wire a GFCI/switch combo?" is helpful. But I want to see a diagram for a situation where the power ...
7
votes
5answers
11k views

What could be causing AFCI breaker and GFCI receptacle nuisance tripping?

I have a very unusual set of electrical issues that have proven difficult to troubleshoot. I live in a newly constructed house. Each bedroom has AFCI breakers. In the past 3 years living there, the ...
7
votes
1answer
25k views

Why doesn't my GFI receptacle reset?

I have a GFI receptacle in my kitchen that feeds four other receptacles. It tripped the other day and I cannot get it to reset. All of the other receptables on the circuit are not functioning which ...
6
votes
2answers
6k views

Why does my GFCI outlet trip as soon as the breaker is turned on?

I have an outlet feeding other outlets about 50 feet away. All the outlets are outdoor enclosed in a protective weather cover. Today I wanted to replace one of the receptacles with a GFCI so all the ...
2
votes
3answers
3k views

How to independently switch a GFCI outlet?

I would like to add a plug outside where each plug would be independently switched. The use of this is to be able to switch a rope light and a fan separately. This is being added to a new breaker so ...
13
votes
4answers
80k views

How do I properly wire GFCI outlets in parallel?

I have two countertop outlets in my kitchen that I am in the process of replacing with new, GFCI-protected outlets. These two outlets are on a circuit together, and they are the only loads on that ...
6
votes
4answers
37k views

Why is GFCI tripping on refrigerator circuit?

My refrigerator is tripping the GFCI on the socket into which it is plugged. Searching about this topic seems to indicate that this is a reasonably common complaint. However, I can't find any ...
6
votes
3answers
15k views

Are non-GFCI outlets that are downstream of a GFCI outlet ground fault protected if they are fed from the GFCI outlet's load side?

Are non-GFCI outlets that are downstream of a GFCI outlet ground fault protected if they are fed from the GFCI outlet's load side? If those non-GFCI downstream outlets were not fed from the GFCI ...
4
votes
1answer
5k views

How can I add a GFCI breaker on two circuits with a shared neutral without rewiring? [duplicate]

Possible Duplicate: How do I install a GFCI receptacle with two hot wires and common neutral? I have a pool to protect correctly. There is a 12/3 wire: red serves the receptacles at the ...
2
votes
2answers
117 views

Connecting 2 GFCI Breakers to 2 Hot Leads and 1 Common

So I just bought my first house and in lieu of changing loads of outlets in the kitchen for GFCI outlets I went with two 20A GFCI breakers. Upon going to install the breakers I found that the cable ...
5
votes
6answers
2k views

Where *shouldn't* I use GFCI/AFCI?

There is a lot of information out there about the benefits of GFCI and AFCI and the places where they must or should be used. But are there any circumstances where you're better off without them? If I ...
5
votes
3answers
4k views

Is GFCI protection required for a dedicated exhaust fan circuit?

I'm considering installing an exhaust fan in my bathroom which includes light and heat, and requires a dedicated 20 amp circuit. Would this circuit need GFCI protection? The instructions for the unit ...
3
votes
1answer
2k views

How to wire a 240V disconnect panel for spa that does not require neutral?

I'm wiring a 240V/60A hot tub which requires 3 conductors; one of these conductors is ground. No neutral is run to the tub. That said, I have a red, black, and green running to the hot tub from the ...
3
votes
1answer
5k views

Can you have a GFCI breaker protecting a GFCI receptacle?

We have electrical outlets in two bathrooms on the same GFCI breaker. I would like to put a GFCI outlet for the only outlet in the guest bathroom so it can be easily reset if tripped. Can this be ...
3
votes
3answers
21k views

How do I wire a GFCI receptacle using two black wires and two white wires?

I recently purchased an older home and wanted to install GFCI outlets in the kitchen. When I opened up the outlet, there were four wires (two black and two white) in addition to the ground. I ...
3
votes
1answer
9k views

How to add GFCI to a box with one outlet controlled by a switch?

I'm pretty inexperienced when it comes to electrical work, though I do know my way around a circuit diagram, thanks to some EE courses in college. I think this is one I can do myself, I just would ...
2
votes
1answer
575 views

Replacing outdoor outlet

How can I replace an outdoor outlet cover that has a stripped center screw? Do I need to replace the outlet as well? Do I need to replace the box that the outlet is housed in if it is coming out ...
2
votes
2answers
314 views

GfCI trips in bathroom

Hi I have a bathroom gfci which is connected to the lights , fan and receptacles in bathroom , bedroom and landing . It's about a 45 year old house . Without protecting the circuits in the bedroom how ...
2
votes
2answers
793 views

What options are there to achieve both grounding/ground-fault and arc-fault protection on old 2-wire circuits?

The three receptacle circuits in my house are 2-wire NM, but have 3-prong receptacles. My electrician recommended and installed GFCI breakers to provide "grounding" to these circuits. I now realize ...
2
votes
2answers
2k views

Can I use a 50 amp GFCI breaker on 15 amp circuit?

I am in the process of changing my hottub over to wood heat. I have eliminated all controls and am running the pump directly from the panel on a double 15 amp breaker (240 volts). I have my existing ...
2
votes
1answer
899 views

GFCI combination switch and outlet to fully switched protected outlet

Before a single screw comes out of the wall, I need to be sure I understand this fully, and rather than type out everything, I made a diagram based on what I was able to dig up on forums. This is for ...
2
votes
4answers
18k views

How can I stop this GFCI receptacle from tripping?

In my garage I have two wall receptacles on opposite sides of the garage. On one side the receptacle is a GFCI receptacle and the other side is a normal one. In the normal receptacle I have a small ...
1
vote
1answer
185 views

Can you wire a 30A 2P standard circuit breaker “downstream” from a 60A GFCI 2p circuit breaker?

Will this still provide GFCI protection? Is this against code? Does this represent a hazard? I have a subpanel with a 60A GFCI circuit breaker, that I want to use that to feed to 2 30a 240v ...
1
vote
2answers
4k views

Why GFCI clicks, even when turned off?

I have a GFCI receptacle that is clicking. Every 5-10 minutes it clicks repeatedly for 1-2 seconds. The GFCI is turned off (the RESET button is sticking out) but it still clicks! What does this mean? ...
1
vote
1answer
1k views

Proper wiring for GFCI given switched circuit

So I've added the 3-prong plug to my garbage disposal, and now I'm on to the GFCI outlet installation. The breaker was not GFCI protected, nor is there a GFCI outlet on the loop. I've gotten to the ...
1
vote
2answers
2k views

GFIC requirements for a Kitchen multi-outlet strip

I was thinking of replacing my current kitchen counter receptacles with a Hard Wired Multi-Outlet strip that would run below my cabinets. My question is How would I provide GFCI protection? Can a ...
0
votes
1answer
226 views

Upgrade from outlet/switch combo to GFCI + outlet

In a bath in my house I currently have a very old (likely original 1949) outlet/switch combo. The outlet is hot, not dependent on the switch being on. The switch controls vanity lights. I would ...
0
votes
2answers
90 views

Change GFCI outlet/switch with regular switch

I have 2 switches in my bathroom: a fan (power comes into the fan and it's just a simple black/white to the switch) and a switch/outlet GFCI combo where the switch powers the lights but the outlet ...