Ground fault circuit interrupter, also referred to GFCI, GFI, or a residual-current device. This devices detects a leak in current, or an imbalance between the current on the hot and neutral wires. This is used to prevent electrical shock.

learn more… | top users | synonyms

0
votes
1answer
98 views

GFCI combination switch and outlet to fully switched protected outlet

Before a single screw comes out of the wall, I need to be sure I understand this fully, and rather than type out everything, I made a diagram based on what I was able to dig up on forums. This is for ...
0
votes
1answer
57 views

Why does my GFCI receptacle trip when anything is plugged in?

My house was built in 1994. The garage is fed from one 20amp circuit wired to the lights first, then a GFCI, then a couple regular outlets. This has worked fine for me for 19+ years. We had a ...
1
vote
2answers
893 views

Why isn't my GFCI receptacle working?

I am installing a GFCI outlet and I am having some issues. I have identified the hot and neutral wires. They test positive with the voltmeter when I turn on the switch. I connect the receptacle to ...
4
votes
4answers
227 views

What could be tripping multiple GFCI breakers?

I have 14 ground fault circuits split 7 on each side of my panel. I have recently had 5 or six trip on the left side and 1 or 2 on the right. It happens at all hours. It appears I have some kind of ...
6
votes
3answers
6k views

What could be causing GFCI breakers and receptacles to trip?

I have a two wire system and after installing GFCI outlet in kitchen I realized there is a problem with some type of inconsistancy causing the GFCI to trip as soon as power is sent to it. Thinking the ...
2
votes
1answer
38 views

Is my water heater connected to GFCI and is it affected after short circuit?

I am an absolute n00b when it comes to home electrical systems. Please do forgive me if this is a repeat question since I wouldn't know what to search for. I am in France and I have 230V supply at ...
1
vote
2answers
97 views

Why does my fluorescent ceiling fixture trip the GFCI sometimes?

Every so often, roughly a 1/20 chance, flipping the light switch to my laundry room's fluorescent fixture will trip the nearby GFCI outlet. Why is this? Is it more likely to be the GFCI being faulty ...
2
votes
1answer
200 views

What size GFCI and receptacles on 20A circuit?

I am adding a string (5-6) of receptacles to an existing 20A circuit in my basement that currently has just one 15A duplex receptacle on it (with 12/2 Romex). I am planning to replace the existing ...
5
votes
3answers
199 views

GFCI outlet hot when nothing's plugged into it

Using a thermal camera (coolest thing in the world, by the way), I discovered that a GFCI outlet in my bathroom is hotter then the surrounding wall when nothing's plugged into it: It's not boiling ...
0
votes
0answers
24 views

GFCI circuit partially works

While making coffee using downstream outlet, it just stopped. My GFCI outlet works and it isn't disconnecting. The test button also works but downstream outlets don't. What would cause that? ...
0
votes
1answer
37 views

GFCI connection and trip

I have 1 GFCI in the bathroom On the 1st floor. The line side is sourced from the main board, and the load side has 3 standard duplexes in the 2 bathrooms on the 2nd floor. After moving in to test the ...
5
votes
3answers
104 views

Does big current draw make GFCI outlets go bad?

About 2 years ago during a kitchen update, I replaced a GFCI outlet with a new one, 20-amp (both pass through and the GFCI outlet itself). Branching downstream from it are two more outlets, one on the ...
2
votes
3answers
730 views

How can I remotely monitor a GFCI receptacle?

How can a sump pump in a crawl space only accessible by crawling down a hole in a closet have its GFCI protected outlet monitored from the living room? I am imagining the best way to run the pump is ...
2
votes
1answer
107 views

How can I repair a ground-fault?

I'm hooking up a new GFCI in a remodeled bathroom, replacing an older one. There are two outlets following on the circuit. The GFCI works fine, but as soon as I would plug a light into the next ...
2
votes
2answers
108 views

What could have caused my GFCI to trip, and what can I do about it?

About a week ago, a GFCI tripped. I noticed that because appliances in my kitchen stopped working. The short story is that something was put into an outlet that shouldn't have been. That's not the ...
0
votes
1answer
53 views

Can I put a switch in after a GFCI and still have proper protection?

I am about to install a fan in the shower stall. It is code to do so as long as the fan is GFCI protected. However, I don't want the switch that controls the fan to turn the receptacles on and off. ...
0
votes
2answers
69 views

None of the outlets in the kitchen are working

The other day I switched on the garbage disposal and now none of the outlets in the kitchen work. This circuit is GFCI protected from the panel but the GFCI breaker in the panel is not tripping. When ...
13
votes
3answers
18k views

Which Kitchen outlets do NOT need GFCI?

I have the 2 circuits in the kitchen with GFCI outlets, but I'm not quite sure which other ones do NOT need GFCI. Other circuits in the kitchen include Microwave, Fridge, and Dishwasher. It makes ...
1
vote
2answers
123 views

GFIC requirements for a Kitchen multi-outlet strip

I was thinking of replacing my current kitchen counter receptacles with a Hard Wired Multi-Outlet strip that would run below my cabinets. My question is How would I provide GFCI protection? Can a ...
2
votes
1answer
123 views

Replacing outdoor outlet

How can I replace an outdoor outlet cover that has a stripped center screw? Do I need to replace the outlet as well? Do I need to replace the box that the outlet is housed in if it is coming out ...
0
votes
1answer
66 views

Will chained GFCIs malfunction?

What I'm asking is if a GFCI wired onto the load of another GFCI will function? Will it cause the upstream one to malfunction. Will it cause the downstream one to malfunction? It is against code? ...
0
votes
0answers
70 views

Why don't I have power at my GFCI outlet?

Sorry for what will likely be a long question! It all started with a bathroom light that would not turn on, even though the bulb was good. I decided to get my multimeter and see if the switch was ...
10
votes
1answer
4k views

Can I add a standard receptacle on a GFCI circuit

So, I want to add a receptacle in the bathroom (I tend to run out of batteries on my phone while crapping at the end of the day). There's a GFCI outlet on the other side of the crapper wall that ...
8
votes
3answers
2k views

Is it possible to be electrocuted from a properly functioning GFCI circuit?

It's my understanding the the purpose of a GFCI circuit is to prevent shock by tripping the circuit if there is an imbalance in current in vs. current out. So my question is, if you have a functioning ...
2
votes
2answers
153 views

Did I damage the breaker by incorrectly wiring a generator?

During a power outage I attached my generator incorrectly (I have never done this before - I just was not paying attention). Anyway, I crossed the ground at the box with the black. When I turned on ...
4
votes
3answers
2k views

Why does my circuit breaker trip with any small load, even after replacing the breaker?

I have a 20A 240V GFCI breaker in my main breaker box going to a conduit to another breaker box outside. All worked well last summer. Now, when I put any load (weed-eater, light, etc.) on an outlet ...
0
votes
0answers
23 views

Wiring GFCI receptacles using 4 wire 240 circuits [duplicate]

The house I am renovating was wired with 4 wire 240 circuits. Probably to save pulling extra wires or to save costs. I did a gut demo so all wiring is exposed. I ran one of the "old" 4 wire 240 ...
3
votes
2answers
680 views

How can I find the first receptacle in a circuit?

I know how to wire a GFCI receptacle and all the things to go with it in doing so. But what I do not know is the following. I understand the GFCI receptacle should be first in line to protect the ...
2
votes
2answers
2k views

How can one whole group of outlets stop working, but the wires to one plug on one outlet are still hot?

I have a bank — circuit? — of outlets in the kitchen that have stopped working. One of these outlets is a GFCI but it is not tripped. The breakers for all the kitchen outlets have not tripped but I ...
4
votes
3answers
893 views

Should I use a GFCI or AFCI circuit breaker with knob and tube wiring?

My American house was built in 1942, and much of the wiring is still knob-and-tube wiring (2-wire, no ground). Over the years new modern wiring has been added to the house, but we still have some KnT ...
1
vote
1answer
300 views

Can I install two GFCI receptacles on a multiwire branch circuit?

I am wondering if I'm using a 10/3 teck cable to power two 20 amp GFCI receptacles for a temporary power situation, can I use two separate single pole 20 amp breakers at the panel for each receptacle. ...
1
vote
1answer
82 views

Wiring requirements for garage and bedroom addition

I've just added a new garage and bedroom and am about to wire them. I've done a lot of wiring in my house, know all the basic requirements for how wiring is run, etc, never had a problem with ...
0
votes
0answers
66 views

Why does a GFCI breaker and receptacle on the same circuit cause tripping tripping?

I work in the apt industry as maintenance, currently on a new property. I had a call this weekend about no power in kitchen outlets or dining room. I found a GFCI outlet in the run, tried resetting it ...
3
votes
1answer
148 views

How can I provide GFCI protection to my kitchen receptacles?

I Live in Round Lake, Il., in a 1940's built home. In my kitchen I have four counter top receptacles surrounding my sink area. Two of the receptacles are close to the sink, and I want to replace them ...
2
votes
1answer
91 views

GfCI trips in bathroom

Hi I have a bathroom gfci which is connected to the lights , fan and receptacles in bathroom , bedroom and landing . It's about a 45 year old house . Without protecting the circuits in the bedroom how ...
3
votes
1answer
1k views

Sump Pump Trips GFCI Receptacle. Is a single, dedicated non-GFCI receptacle safe?

I recently replaced my sump pump in one of my two sump pits. To comply with codes, I replaced the outlet with a GFCI type outlet. Unfortunately, once I turn the power back on, the GFCI trips ...
0
votes
1answer
80 views

Is it an offence if my landlord has no GFI's in the house and outside of the house? [closed]

I live in Gloucester Ottawa and there is no GFI's in our townhouses. I have general knowledge of electrical codes. Winter is approaching and I don't feel like getting electrocuted when I plug in my ...
0
votes
0answers
26 views

dual GFCI circuits with multiple protected outlets, all sharing a neutral [duplicate]

I'm trying to wire two GFCI circuits sharing a neutral. The line is coming in from a 2-pole circuit breaker. I want to have two circuits at each location, each protected by a GFCI upstream. ...
6
votes
5answers
5k views

What could be causing AFCI breaker and GFCI receptacle nuisance tripping?

I have a very unusual set of electrical issues that have proven difficult to troubleshoot. I live in a newly constructed house. Each bedroom has AFCI breakers. In the past 3 years living there, the ...
11
votes
5answers
48k views

How do I install a GFCI receptacle with two hot wires and common neutral?

In my kitchen, I want to replace a regular 120V receptacle with a GFCI-protected receptacle. The instructions describe what to do with a regular 2-wire + ground feed, with and without daisy chaining ...
3
votes
2answers
748 views

Why does a GFCI trip when anything is plugged into the other outlets?

There is one outlet with the GFCI and several other outlets without. The GFCI outlet works fine, while anything plugged into the other outlets causes the GFCI to trip. How should I detect and fix ...
4
votes
1answer
558 views

What problems could occur if I plugged a 3-prong plug into a receptacle labeled “No Equipment Ground”?

I have several old, ungrounded outlets in my house which are protected with GFCI, which is allowed per code as the GFCI will protect a person in the event of a ground-fault. These outlets are ...
1
vote
0answers
199 views

Why do I have a 3 wire/double pole breaker for kitchen receptacle?

I am switching my kitchen receptacle to a GFI; it has 3 wires. I'm pretty sure I have to break the bar between the two hot screws, thus making the top and bottom on a separate circuit. What is the ...
2
votes
2answers
224 views

Why is my GFCI receptacle tripping when I add another receptacle to the circuit?

I have 3 receptacles in my garage. One is a GFCI which protects all 3 outlets. I want to connect a new receptacle off the third receptacle (end of run) on other side of wall, and have it protected by ...
2
votes
2answers
265 views

Will a GFCI device work on circuit where the neutral is switched?

How well will a GFCI circuit be able to detect current flows, if both the "hot" input and the (supposedly) "neutral" input to a GFCI outlet are energized? The reason I am interested in this is that I ...
1
vote
0answers
133 views

Washer tripping gfi outlet

I've been living in my house for almost two years and my washer and dryer have been working fine. I have a maytag Neptune washer and dryer, just the other day I took a packet of tide washing machine ...
6
votes
2answers
2k views

Why does my GFCI outlet trip as soon as the breaker is turned on?

I have an outlet feeding other outlets about 50 feet away. All the outlets are outdoor enclosed in a protective weather cover. Today I wanted to replace one of the receptacles with a GFCI so all the ...
1
vote
0answers
172 views

How to finish the wiring of a shared GFCI receptacle

My neighbor who is an electrician helped me start an electrical project in my garage but has been MIA for 3 weeks and I'm not sure how to finish the wiring of the receptacles. He didn't seem to start ...
12
votes
3answers
12k views

When to use holes instead of side terminals to wire an outlet

This question comes from Shirlock's comment on this GFCI wiring question. When and why should you use the holes on the back of an outlet rather than the side terminals? I always assumed the holes on ...
2
votes
1answer
128 views

Does this wiring sound right?

First let me preface this by saying that I am very comfortable doing basic electrical work. With this project my electrician is on vacation and won't be back for a few weeks but I wanted to see if I ...