The tag has no wiki summary.

learn more… | top users | synonyms

11
votes
2answers
2k views

What is the optimal configuration of a cross brace on a wooden gate?

I'm building a wooden gate for my deck, and I want to put in a cross brace to reduce sagging. I want to install the brace so that it transfers the load from the top unhinged corner, to the bottom ...
9
votes
2answers
7k views

How deep should I sink a gatepost for a 7' wide gate in my fence?

I am a first time fence builder, which will be 6ft cedar. I need a gate that is 7 to 8 ft wide. I live in Oregon and the frost line is only a foot deep. I was planning on a 7ft gate with a 6x6 post. ...
4
votes
1answer
196 views

Metal gate in hot weather

Is it possible that our metal gate could be expanding in the hot summer weather? It has been well over 100 degrees daily on average for a month or so, and for some reason a metal gate we have had for ...
3
votes
4answers
815 views

How do I prop-up or fix a wall that is slowly moving?

In the image, the single stack of breeze blocks on the right hand side has been slowly moving away from the wall over the last 4 years. The gate latch (also on the right hand side) is now rubbing ...
3
votes
1answer
162 views

Wooden pale fencing

I want to replace some fencing in the back garden. Ideally (if I can find it) I want to do this with Convex Pale Fencing. The fence is around 3 ft high x 6 ft wide, and I'll be using 3 panels ...
2
votes
2answers
8k views

What size posts do I need to use to build a wooden driveway gate?

I have just built a 6 foot fence all the way around my property. To finish it offI need to build a driveway gate. The gate will be 15 feet wide and have two swing gate sections. I have used 4x4x8 foot ...
2
votes
3answers
63 views

How can I attach a safety gate at the bottom of the stairs?

I have a wall on one side with trim molding at baseboard and opposite end is the wooden banister. What type of gate can I attach. The drywall is not holding the screws in place and we we frequently ...
2
votes
1answer
1k views

What gauge fence post should I use for a 36" wide wooden gate?

I want to attach a gate to a fence where the fence will be attached to a 2 3/8 in. metal post. What gauge should the post be for proper support? The fence will be a six foot wooden fence, as will ...
1
vote
2answers
1k views

Painting an old metal gate with some corrosion

I have a front gate to my house that I would like to repaint I have few issues. First there are a few spots with rust And some with general corrosion Also I wonder how to paint around where the ...
1
vote
1answer
221 views

How can I keep an entry gate operating during a power outage?

I have an electric sliding gate, with a motor powered by 220V. The problem with this kind of solution is that, when we have a power supply failure, we must remove a screw and open it manually. It ...
1
vote
2answers
887 views

How should I protect wood gates in a damp climate?

I would like to make a set of external timber yard gates, i.e. both sides of the gates will be exposed to the elements. Since I live in the North of England, it tends to rain. In order to avoid the ...
1
vote
1answer
427 views

What height concrete gate posts do I need for a 4 foot high gate?

The gate is 4ft high by 4ft wide for a garden path and is a standard quality metal gate, so not very heavy.
1
vote
0answers
39 views

14ft wide wood gate construction [duplicate]

I am putting a gate across my driveway which is 14ft between posts on either side. Its going to be wood and all 1x6 and 1x8 lumber to keep weight down. Each gate will be about 7ft long so I was ...
0
votes
2answers
3k views

How should I build a wooden gate?

I wish to build a gate across a 3.8m wide driveway. There is a concrete column on one side which I can fix the hinges to (a post into the ground is not an option) and a brick wall on the other side ...