1
vote
1answer
73 views

Are pocket screws strong enough for a bed frame?

I've built a loft bed for my 4 year old following the plans posted here: http://ana-white.com/2012/07/plans/camp-loft-bed-stair-junior-height I modified the plans slightly to use a ladder instead of ...
0
votes
2answers
103 views

Using wood filler on garden furniture

I want to repair some weather battered garden table, bench and chair set. It has had some in places, so I will be replacing the severely rotten sections, and scraping out the rot from the partially ...
7
votes
1answer
212 views

Is there a more rugged finish than Polyurethane for a heavy use table?

A few years go I sanded a stained table we had. Upon doing so, we discovered that it had really nice wood underneath. So instead of restaining, I applied about 4 coats of satin polyurethane. It looked ...
1
vote
1answer
848 views

How do I turn my top-heavy headboard into a freestanding headboard?

I've DIYed an upholstered, king-sized headboard (5'x6'10"), but after trying to bolt it to the bed frame, I've realized that the bed frame is much too light to prevent the headboard from toppling ...
6
votes
3answers
654 views

How to connect wood to concrete

How can I attach wood to concrete in this bench?
2
votes
1answer
208 views

How to build a wooden ladder for a loft bed?

I want to build a five foot ladder for my 6 ft loft bed that's being cut down to 4ft tall because it's too close to my ceiling. My bed is going to be in front of my window which is on my shortest ...
6
votes
4answers
347 views

Are small air bubbles on the surface while applying wood finish normal?

While finishing my door, I've noticed a lot of small air bubbles after applying the finish. I asked a painter about it and he told me it's normal, but it doesn't seem normal to me. Is this normal or ...
4
votes
1answer
3k views

How is a floating desk top supported against the wall?

Example of a floating desk top (courtesy of Phil Curtis): With increased height, it'd be one of simplest standing desk designs, and I am planning to do this at home. But, I am not sure how ...
5
votes
1answer
6k views

How do I build a corner bench for my deck?

I am totally new to DIY and wanted to take my first steps with a simple project - a corner bench. I have decking outside already, and want to use the same decking wood for my bench. Something similar ...
2
votes
2answers
109 views

Can my garden furniture be saved?

I have some hand me down wooden furniture. Unfortunately, with multiple moves and births in the last few years, it has gone a unloved. The wood seems very weak, and is brittle when dry. One beam ...
5
votes
6answers
728 views

How do I prevent doors on a media cabinet from sagging?

A friend and I have just built a floor to ceiling media shelf unit for DVDs. It has 9 shelves and is about 3' wide. The frame around it is made up of 2"x8" boards and the shelves (except for one in ...
4
votes
5answers
7k views

How can I mount a desk on a wall with L-brackets?

I'm currently planning a new wall-mounted computer desk and intend to use something similar to this as the top: However, my end goal is for a wall-mounted desk, using L-Bracket mounts. I've never ...
2
votes
1answer
3k views

Can I use two 2x4's to replace 4x4 posts in a loft bed?

I'm building a loft bed for a queen size bed. I planned to build a platform and support it with 4x4s, but I'm having trouble finding untreated 4x4s. I plan to loft the bed 5' or so. The platform will ...
2
votes
1answer
497 views

How can I make a park bench more sturdy?

I purchased a park bench for my patio But it's a little on the flimsy side and I'm afraid someone is going to throw themselves down on it and it's going to break. In what way can I strengthen the ...
2
votes
2answers
503 views

Which technique of wood joining is the best for joining these boards of a small table?

I want to join these four 1.8 cm thick beechwood boards as one can see on the picture. My idea is to join at the B points with biscuits but I’m not sure what to do about the A points. It needs to be a ...
3
votes
2answers
421 views

What type of wood should I use to resurface my table?

A club at uni has this great big old table. (about 1220mm by 2420mm). The club in question is the gaming club, so pen and paper RPGs, card games, boardgames, warhammer. fairly rarely models are ...
8
votes
2answers
282 views

How can I remove a moisture mark from a wooden table?

I have a white mark on my wooden dining table that was caused by a potted plant sitting there for too long without a saucer. Attempts to clean it off have been futile because it seems not to be a ...
1
vote
0answers
310 views

Where can I find 3D models of objects that are more like real things? [closed]

I'm searching for furniture and related models (TV rack, TV, freezer, armchair...) for my 3D flat's design. Sweet Home 3D and Google SketchUp have a lot of models, but I would like to use models of ...
2
votes
3answers
903 views

What is a good wood to use to build a base for a heavy antique table top?

So my gf has a really sweet antique baker's table top. It has what I believe is a porcelain but may be ceramic finish. I've never tried lifting it (it was here before I was) but she tells me it ...
1
vote
1answer
833 views

How do I attach a shelf to a plaster wall invisibly?

Following this question: How can I attach two pieces of wood in an invisible way? I have another - what would be a good way to attach a shelf to a plaster wall, if it is completely supported (i.e. ...
7
votes
1answer
807 views

Table with 45 degree corner groove

I'm not a carpenter, so forgive me if this is obvious. Also, I'm Brazilian so forgive my English. I want to build a table with only 3 MDF plates, but I want the corners to have "45 degree grooves", ...
5
votes
1answer
260 views

Am I doing something wrong with this sanding job?

I'm trying to finish a finishing job on a dresser; I abandoned the project (long story) a while ago after getting a few drawers done, and I've since lost the exact instructions I was following. After ...
7
votes
3answers
11k views

What is this soft, sticky wood finish and how do I remove it?

We have a second-hand table with a mysterious finish. The wood underneath is pale, possibly pine. With the finish, it's a slightly darker and "warmer" colour. The table is not antique; I'd guess only ...
4
votes
3answers
3k views

How can I repair screws in furniture with stripped holes?

I'm trying to repair a piece of furniture from which several screws have pulled out, stripping the wood. It's a lift top coffee table, such as this. (This is NOT the model in question, this just ...
19
votes
13answers
56k views

What are cheap ways to build strong shelves with a large span?

I have removed several old and moisture damaged built in storage units from my house. I would like to replace them with shelving. There are a number of different sized gaps (width and depth to fill). ...
5
votes
5answers
6k views

What's the right way to sand/shave/reshape particleboard?

My second bedroom has low ceilings. I bought an IKEA closet, but somehow botched the measurements when I was seeing if it would fit. So, instead of having ~10cm of room for the top of the cabinet, I ...
3
votes
3answers
864 views

How should I paint pine furniture?

I built a bed for my son out of Pine (from plans on the internet.) I am going to paint it white. What kinds of preparation do I need to do to the wood, especially considering the 4 posts are from ...