For questions generally relating to the internal structural members of a home or other structure that form walls, ceilings and roofs, including studs, plates, headers, beams, and joists.

learn more… | top users | synonyms

0
votes
3answers
43 views

How should I nail blocking?

I am struggling to efficiently add blocking to 16" stud bays when I can't end nail through the other side of the stud. I have a full-size nailer, a palm nailer, and a hammer or two--but not a lot of ...
4
votes
2answers
3k views

How can I build deck stairs flush with the end of the deck?

I have a deck design where I want stairs coming down perpendicular to the joist starting at the end of the joist. You can see the picture as a generic not to scale drawing of what I mean. I had ...
2
votes
2answers
106 views

Need to install wood framing in a pipe filled wall to be able to hang shelving

I've got this wall, from which I've ripped off the drywall. The wall is 5' wide, 9' high. There's 4 flimsy metal studs and I'd like to install a few big sheets of plywood over those so I can put up 6 ...
2
votes
1answer
35 views

Can I build a car-port on the side of my garage?

I have a 2-car attached garage but three cars in the household. While I'm obviously aware I can just leave the third car in the driveway, it inconveniently blocks the cars in the garage and in the ...
1
vote
1answer
28 views

Installing a wall vent when stud blocks the opening?

I'm installing a rear duct range hood and need to open a ~4"x18" hole through the exterior wall. A 2x6 stud blocks the hole. I plan to cut the stud and place a header, jack studs, and sill around ...
0
votes
1answer
92 views

Why are 3-1/2 (16d) nails so hard to find?

So I'm a little confused. It seems like 21 degree fullhead framing nailers are fairly standard. According to the ...
2
votes
0answers
65 views

Will my garage truss and beam configuration be adequate for a room in the attic?

I am getting ready to finish some of the space above the garage and have some questions. I am located in Pittsburgh, PA. The garage is sloped on both sides down to the floor. I was going to utilize ...
1
vote
0answers
42 views

What's the best way to cut through this wall?

I am adding insulation+drywall between open rafters. What's the best way (tool, blade/bit, technique, other advice) to get through these wall layers for ventilation? (I'll put mesh and grilles over ...
1
vote
0answers
45 views

Can you lay subfloor on concrete before framing interior walls?

Our unfinished basement has a concrete floor and poured concrete walls. It has stayed completely dry all year for a decade since the house was built. I will be framing the exterior walls 1" from the ...
1
vote
0answers
35 views

Where can I find drawings of a mobile home's construction?

I bought my very first trailer/mobile home last August. I've never lived in one, never spent significant time in one, know less than nothing about them. That said, I have a doublewide 90 Commodore. ...
1
vote
0answers
45 views

Does the junction between two horizontal spaces need to be fireblocked?

This question is in regard to interpretation of IRC:2012 R302.11 for a single family dwelling. It is clear that junctions between vertical and horizontal framing need to be fireblocked (e.g. between ...
1
vote
0answers
145 views

Sistering stingers to convert stairs from closed to open stinger

I have a set of existing closed stringer stairs with a full wall on the left and half wall on the right. I am looking to remove the full wall and modify both sides of the stairs to an open style. I ...
1
vote
0answers
86 views

How do I frame in the open front of a 12' high shop/garage building

My building is 32' wide, 26' deep by 12' high. I believe it was built as a carport for RV and other vehicles. The 3-walls use 2x4's 24"oc - the front opening has a good sturdy header that runs the ...
0
votes
0answers
3 views

Cosmetic fix for installing decking board when not parallel to house?

I am expanding the deck that goes very far (35 x 48 feet ~ 1000 sqft). So I am pretty sure the further end will not perfectly parallel to the house. It could be 1-2 inch off from one end to the other ...
0
votes
0answers
14 views

Would adding ceiling joists in combination with a ridge beam reduce the reaction force of the ridge beam supports?

so think of a normal coupled roof design, with ceiling joists acting as ties for the rafters, except the rafters aren't attached to a ridge board, but a structural ridge beam. Would this configuration ...
0
votes
0answers
36 views

Solid wood beam size for deck 12' span post to post.

What size solid wood beam do I need for a deck that spans less than 7' from the house to the beam. The beam would have a span less than 12' from post to post.
0
votes
0answers
215 views

Framing half-wall in basement to full wall over exterior wall

Debating on whether this is something I can do or if I need to call in an pro. I have a basement room I'm looking to use as a theater room, and I need to finish a wall to the ceiling so I can hang a ...
0
votes
0answers
119 views

Drywall over 2x2 Studs in Basement

I have a basement that is a complete product of the 70's. Faux ugly wood paneling, brass ugly sconces, old school metal work boxes, and a beautiful white drop ceiling. I know I could just drywall over ...
0
votes
0answers
57 views

Finished basement with just painted concrete walls

I have a house from 1955, where the basement has been finished with lighting, carpet, interior walls, etc. I don't know when it was finished, only that it was so when I moved in. The strange thing ...
0
votes
0answers
59 views

What are some relatively cheap options for finishing a room in a barn to be used as a workshop/garage?

I am looking at setting up a wood shop in a room in an old barn and am trying to come up with some good options for finishing/minimizing moisture. The exterior barn walls are concrete and the interior ...
0
votes
0answers
52 views

Can I use braces to fix squeaky floors?

I have quite a few squeaky floors in my 6-month-old house. The main floor plywood (glued and nailed) got rained on as it was being assembled. My basement is unfinished. I would like to do some repairs ...
0
votes
0answers
1k views

Replacing Load-Bearing 2x4 wall with beam and posts - Basement

I would like replace a 64" section of a load bearing wall with a beam and 2 support posts. The current wall is 2x4 pressure treated sill plate on top of poured concrete, 5 2x4 vertical supports and ...
0
votes
0answers
40 views

Costruction specs for cabin

Building a simple cabin 20 x 30 feet single story with gable roof. What size should the ceiling joists and roof rafters be? Roof rafters run across the 20' span.
0
votes
0answers
285 views

What is the minimum thickness of an insulated bathroom wall

I am trying to build a basement bathroom in the corner of the house. Where I am, basement insulation codes are R10/13. What is the minimum that I can do to frame and insulate a wall. The two ...
0
votes
0answers
49 views

Asbestos in close proximity of floor repair

I have a floor repair to make in a 1950's home that had the large in floor central heater installed that has long been removed. The owner wants the grate removed and flooring toothed back in, matching ...
0
votes
0answers
463 views

Add floor framing using joist hangers?

I have a single story ranch where a corner of the house I believe was a car port. The roof line and walls all are framed such that it was always under the roof and considered part of the house, ...
0
votes
0answers
299 views

Can turnbuckles hold a frame in tension?

I'm building a king-sized bunk bed using a loft/joist design. Basically, I've got (see below): slats nailed into joists joists joined to headers with blind tenons headers joined to posts with blind ...