For questions generally relating to the internal structural members of a home or other structure that form walls, ceilings and roofs, including studs, plates, headers, beams, and joists.

learn more… | top users | synonyms

1
vote
2answers
529 views

Framing a door ON stairs, 3 steps to landing?

I have to build a door frame on a staircase. Problem is, at the bottom of the staircase are already 3 doors on all the walls, so putting another door right at the bottom of the stairs (on the ...
4
votes
2answers
328 views

What's the right way to insulate and frame around this pipe?

I have been studying the latest engineering on how to insulate and frame basements after tearing out a partially finished basement that had wood and insulation in direct contact with the concrete. ...
1
vote
1answer
59 views

Building an archway

As part of a much larger building project, I will be replacing a 12 foot section of wall between two rooms, which includes removing two 2x4s and one 4x4. The 4x4 is due to the house being built using ...
1
vote
2answers
64 views

2x4s in hall closet

I am sawing an opening in the side of my protruding hall closet because it's the only place in my apartment that has room for a wine fridge. My plan was to find out where the framing was after ...
0
votes
1answer
404 views

How to install dryer ducting inside existing wall?

I'm thinking about installing a recessed dryer box like this. http://www.homedepot.com/p/Dundas-Jafine-Recessed-Dryer-Vent-Box-DRB4XZW/202449693 Apparently with 4" studs you have to compress the ...
2
votes
2answers
134 views

Need to install wood framing in a pipe filled wall to be able to hang shelving

I've got this wall, from which I've ripped off the drywall. The wall is 5' wide, 9' high. There's 4 flimsy metal studs and I'd like to install a few big sheets of plywood over those so I can put up 6 ...
0
votes
1answer
91 views

Are 2x4 rafters legal in Connecticut? 13 ft runs

so I bought a REO house and about to redo the roof above the garage. I've noticed that I need to replace some rafters. However - I'm seeing that rafter are 2x4... Is that code-legal? p.s. by 13 ft ...
0
votes
3answers
478 views

Knee Wall Without Top Plate

I'm finishing our attic and I can't quite figure out the best approach. The house came with the attic already "framed" with a kneewall, but the studs are just just angled directly into the rafters ...
0
votes
1answer
98 views

16' Tall Load Bearing Wall

I am planning to build a 12'x12' cabin. I cannot go bigger than 12x12, but there are no height restrictions so I'd like to incorporate a loft. I'm thinking front wall at 16' tall and rear wall at 12' ...
0
votes
0answers
39 views

Solid wood beam size for deck 12' span post to post.

What size solid wood beam do I need for a deck that spans less than 7' from the house to the beam. The beam would have a span less than 12' from post to post.
0
votes
0answers
245 views

Framing half-wall in basement to full wall over exterior wall

Debating on whether this is something I can do or if I need to call in an pro. I have a basement room I'm looking to use as a theater room, and I need to finish a wall to the ceiling so I can hang a ...
0
votes
0answers
129 views

Drywall over 2x2 Studs in Basement

I have a basement that is a complete product of the 70's. Faux ugly wood paneling, brass ugly sconces, old school metal work boxes, and a beautiful white drop ceiling. I know I could just drywall over ...
5
votes
3answers
338 views

Why is blocking never placed “sideways”?

If you are blocking for structural strength (not fire protection or nailing surface), wouldn't it be better to put the 2x4s sideways, oriented the way they would be in a built-up header?
0
votes
0answers
59 views

Finished basement with just painted concrete walls

I have a house from 1955, where the basement has been finished with lighting, carpet, interior walls, etc. I don't know when it was finished, only that it was so when I moved in. The strange thing ...
2
votes
1answer
84 views

False roof frame in ceiling

Have never figured out what this is. There is basically a false roof frame in the attic. The peak is the opposite direction of the actual roof. As far as I know there hasn't been any major remodeling ...
6
votes
4answers
1k views

What is the purpose of horizontal blocks on a bearing wall?

In my basement, the bearing wall has horizontal blocks between each stud, similar to what you see in this picture: . There is one place on the wall where one of the blocks was removed to place an ...
1
vote
1answer
641 views

Is it possible to notch framing studs for installing conduit w/out structure collapsing?

I have a garage which is a simple structure - 4 walls, garage door, and a normal door. The structure is framed as one would expect, studs 16 inches apart. I want to put some extra wood paneling as an ...
1
vote
1answer
561 views

How can I make self-tapping sheet metal screws go into metal studs more easily?

I am framing metal stud walls to hang drywall in my basement. When using self-tapping sheet metal screws to secure the metal studs to the top and bottom stud tracks, it seems like the screws often ...
3
votes
2answers
928 views

Newly framed bathroom wall not square, how bad will the tile look?

I'm in the middle of a new bathroom install and have hit a bit of a snag with a bathroom wall being out of square. This bathroom was just framed from scratch, and as you can see from the attached ...
0
votes
1answer
187 views

Framing a window directly through a post in post-and-beam construction?

I have a single story home built on a concrete slab using post and beam construction. I have 4x4 posts spaced 5 feet apart along the exterior wall with 4x8 beams holding up a 4" tongue and groove roof ...
1
vote
1answer
211 views

Do building codes allow smaller nails when using gun instead of manually hammering?

I would like to use a framing nail gun for a bathroom addition. Do people usually substitute a shorter nail for 16d 3.5", but keep the same quantity and spacing? Does that pass code?
1
vote
1answer
65 views

Increasing subfloor thickness under new shower pan

I ripped my old shower down to the studs and joists. The studs were rotten, the subfloor was rotten, and the top of the joists (in some places) were weak and rotten. I plan on replacing some studs ...
0
votes
1answer
38 views

Framing new wall/door

I have a dining room that I want to convert into a home office. There are two openings that I would like to close up and put doors in. Here is a rendering of both locations: I made an attempt at ...
4
votes
1answer
1k views

Can I attach drywall directly to a wood beam?

I'm finishing my basement and need to build a soffit around the HVAC trunks, pipes, and a wood beam. I'm planning to build a ladder on one side of the ducts and another between the ducts and the beam....
2
votes
1answer
454 views

Remove closet center support beam?

I have a bump-out closet in an addition. It had two sets of bi-fold doors, separated by a beam in the middle. The beam seems to bare very little load, and I'd like to remove it for one continuous ...
1
vote
1answer
225 views

How do I remove the carbon brush holders from my HD 77 Skil saw?

How do I remove carbon brush holders from a Skil Saw model HD-77 ? I have removed the set screws from the casing that retain the brush holders. The The motor casing is split to view the holders ...
3
votes
1answer
91 views

What is longest distance without attaching a top plate of interior wall

I have an interior wall in a building with metal roof trusses and drop ceilings. There are no wooden truss members or joists to attach the top plate of the wall. The interior wall will attach to an ...
2
votes
1answer
135 views

What is the difference between LVL 1.9 and 2.0?

A structural engineer gave me a header design using beams made from LVL 1.9. Looking around, I'm seeing more LVL 2.0 available locally. What is the difference?
1
vote
2answers
236 views

4 King studs or 4 Jack studs

I have a 78 inch opening between two studs to install exterior French doors in a load bearing wall. I have a 72 inch door on order (actual size is 71 1/2 inch) To get to the 72 inch opening, I was ...
3
votes
1answer
171 views

Should there be waterproofing between the rim joist and ledger on new construction?

My new house is being built with a deck and I noticed that the framer has fastened the ledger directly to the rim joist without any sort of waterproofing between. The sheathing which is Zip system ...
1
vote
1answer
162 views

How would I go about installing a prehung door in this opening?

I've got an actual opening of 35.5" in an opening between my basement and garage. I'd like to install a prehung door (first time), and am a bit confused about the width necessary for framing. My ...
0
votes
2answers
270 views

building garage what is proper way to frame an 8 ft garage door

concrete base is 6" high and is 8 Ft wide. I am in the process of framing a 16 ft X 18 ft garage
1
vote
1answer
157 views

Screws or nails for securing 2" lumber to overhead joists as fireblocking?

I will be installing fireblocking as part of finishing my basement. I plan to leave about an 8" gap between the newly framed walls (metal stud framing) and the cinder block foundation wall to avoid ...
1
vote
3answers
201 views

prevent splitting w/ nailgun in small pieces of wood

I'm using a framing nail gun to re-build some stairs. This is my first time using a nail gun so I'm inexperienced. There are some small pieces of wood that are used in a corner to support the last ...
1
vote
1answer
553 views

Stud wall that doesn't connect to ceiling?

I am going to be framing out a stud wall in a bathroom for a new walk-in shower. The room has tall vaulted ceilings and I do not want this new shower wall to go all the way up. Maybe just 7-8 feet ...
1
vote
0answers
45 views

Does the junction between two horizontal spaces need to be fireblocked?

This question is in regard to interpretation of IRC:2012 R302.11 for a single family dwelling. It is clear that junctions between vertical and horizontal framing need to be fireblocked (e.g. between ...
2
votes
1answer
3k views

Which method of framing a soffit around rectangular ductwork maximizes ceiling height?

I need to put a soffit around 18"(W) x 8"(H) x 23'(L) rectangular HVAC ductwork in my basement and I am very near to the minimal code requirements for ceiling height for obstructions before adding a ...
0
votes
1answer
178 views

question on the roof structure of my garage

This is a follow-up question on how to carry 20ft lumbers to home. Thanks for the advices and comments. I learned a lot. :) Because the question is now diviated from the original question, I made a ...
2
votes
2answers
731 views

Deck: Connecting Band/rim joist to floor joists

I'm building a deck. Joists are sitting on top of the beam and cantelever over the end of the beam a bit. What is the appropriate way to connect the rim (end of the deck that is perpendicular to ...
2
votes
2answers
784 views

Soaking tub on the second floor: safe?

I am considering getting a soaking tub (pdf here) for my second floor master bathroom. However, I am unsure of how much weight the floor and walls below can support. The house itself is wood frame ...
1
vote
1answer
241 views

Do basement walls with metal framing and foam insulation require fireblocking and draftstopping?

Question: Do non-load bearing basement walls with metals framing and foam insulation (such as extruded polystyrene) in a single-family home require fireblocking and draftstopping? If so, what is the ...
0
votes
0answers
23 views

Sill Plate not Lining up with Foundation Wall [duplicate]

I am in the process of building a one level home in PA. After the formed concrete walls were poured and the framing began, I noticed that on one side of the house that the sill plate was flush with ...
4
votes
3answers
920 views

Should I be concerned that the sill plate is not lined up with the foundation?

I am in the process of building a one level home in PA. After the formed concrete walls were poured and the framing began, I noticed that on one side of the house that the sill plate was flush with ...
7
votes
3answers
338 views

What can I do about a Rough opening that is REALLY out of square?

The house I am living in has a rather interesting problem. Due to what I suspect was Jack Daniels building inspections in this town in the 80's, the footing wall under the second floor dining room ...
0
votes
2answers
866 views

Different options for setting floor joists on top of cinder block foundation

I am in the preliminary phases of a new home design, which I will eventually get run by a professional builder but I am conceptualizing it on my own. So I am exploring different ways to attach the ...
1
vote
2answers
265 views

how to attach framing to this window in concrete?

I'm looking to finish my basement. I have several windows embedded in the concrete as shown in the picture below. I was planning to put framing up in front of the concrete and run some plywood all ...
0
votes
0answers
53 views

Can I use braces to fix squeaky floors?

I have quite a few squeaky floors in my 6-month-old house. The main floor plywood (glued and nailed) got rained on as it was being assembled. My basement is unfinished. I would like to do some repairs ...
2
votes
1answer
168 views

Can it be appropriate to orient a 2x4 “wide side out”?

When we frame walls, we normally orient the 2x4 with the thin surface facing outward. What are the consequences of orienting the 2x4 so that the wide surface faces outward instead? Does the wood ...
2
votes
1answer
88 views

Load considerations on framing members that are only attached to concrete?

I am building out a workshop space in my basement, and want to put up framing on the walls, as shown here: Specifically the left wall and the far wall, both of which have a lip. The foundation ...
1
vote
0answers
160 views

Sistering stingers to convert stairs from closed to open stinger

I have a set of existing closed stringer stairs with a full wall on the left and half wall on the right. I am looking to remove the full wall and modify both sides of the stairs to an open style. I ...