0
votes
2answers
59 views

Is ceiling fan missing grounding wire from the ceiling box, and is this safe?

I recently had a contractor/handyman install a Hunter ceiling fan for me. It worked great, but my wife came home and thought it was too big. I ordered a different Hunter fan, and figured I could ...
1
vote
1answer
96 views

Can I use a 20 amp breaker in the situation of having 15 amp wire connected to a 20 amp main wire?

Can I use a 20 amp breaker in the situation of having 15 amp wire connected to a 20 amp main wire? If I can't would using a 15 amp breaker be ok?
0
votes
1answer
53 views

Networking Phones Together in Building

I have a number siemens optipoint 500 economy phones. They have been used in an office environment in which the networking of the phones were managed by a third party. I would now like to use them in ...
2
votes
2answers
109 views

Options for lubricating wires for conduit?

I am trying to pull four #8 stranded wires through a flexible PVC conduit that is 25 feet long. I can get the wires just a few feet into the conduit before they bind. I know there is a commercially ...
1
vote
1answer
83 views

Should I replace the neutral wire that I accidentally cut in a Romex cable when installing a new outlet?

So I'm installing a new outlet in my home. There's an existing Romex cable that goes up the wall into my attic above the new outlet. When I was stripping the wire to go in the box, I accidentally ...
0
votes
1answer
71 views

How do I wire a door bell?

Can anyone make an educated guess on how to wire so the door bell rings? The flat used to have door phone entry system, but it doesn't work anymore. So it is used as normal bell. In flat we had a ...
4
votes
2answers
200 views

What type of wire should I use to feed a 70 ampere subpanel?

Finishing a basement and I need to add a subpanel. Main panel is outside. Subpanel will be in the basement. 70 Amp breaker in the main to feed the subpanel. I was thinking THHN but would this mean ...
1
vote
2answers
213 views

What gauge wire is typically used for the input to a home breaker box?

I have a moderately-sized home (~2400 sq. ft.) in the United States that was constructed in 1999. I am looking to build a home energy monitor to track my electricity usage versus time. Obviously, in ...
2
votes
2answers
419 views

How do I design the circuit for baseboard heaters?

I am designing the circuit(s) for my basement apartment (cca. 800 sq ft) baseboard heating solution. I am planning to buy Berko HBB Series heaters and distribute them as shown in the below table. ...
3
votes
1answer
451 views

New light switch has blue, black, and white wires. Wall has black, white, and ground. Can I make it work?

I bought a new light switch that is supposed to allow me to automate my lights easier. Here is what it looks like: It has blue, black, and white wires. Coming out of my wall, however, I only have a ...
2
votes
1answer
1k views

Why doesn't my motion sensor light work?

I want to install a simple motion sensor (Lutron Maestro MS-OPS2) on a single pole switch in my garage. When I installed it the light would not turn off. The instructions (PDF) that come with the ...
0
votes
1answer
216 views

Can 22 AWG Solid Copper carry 24 VAC?

I have this irrigation caddy unit, and it requires 24VAC. There's a location outside my house with one ethernet cable and another brown cable with four solid copper wires (black, red, yellow, green). ...
2
votes
1answer
565 views

Is it possible to do two 3way switched circuits that share a common power source but the power source and the light wire are in the same box?

I'm trying to connect two separate circuits from a single power source using 3way switches. My trouble seems that my wire from my light and my power source are in the same box. Is there a way to do ...
5
votes
2answers
484 views

Are the wires for my generator transfer switch undersized?

I purchased a Reliance Q510-C transfer switch to use with a 50 amp generator at my house. The transfer switch is rated at 50 amps. I have wired it into my main electrical box. I also wired a 50-amp ...
4
votes
3answers
545 views

How should I label and organize my home electrical circuits?

I am looking to make the wiring updates in my home extremely simple to understand while doing so in a code-approved manner. I cannot find anything against wrapping a thin band of colored electrical ...
1
vote
1answer
319 views

NEC Definition of “Maintained Spacing” for Wire in Free Air

This seems like a simple question, but I cannot seem to find the answer in the 2008 NEC. There are references to "maintaining spacing" in many sections of the code such as the following: ...
1
vote
1answer
514 views

Multiple Loose-Hanging Wires in Finished Wall

I am re-doing the wiring in my home and I have encountered a situation where I need to run 4 sets of 12-2 NM-B (Romex) wire from my attic down to the same fixture. Per 334.30, I am allowed to leave ...
3
votes
1answer
100 views

Can I install wiring in the space used by a sealed air duct and PVC water supply lines?

I have a space between walls that is about 14" deep and 8 foot wide, and goes from the floor to the ceiling. This space is on the second floor. Petty much in the center of the house. The space ...
0
votes
0answers
538 views

Should I run cable through an always damp crawl space or a dry soffit in the living area?

You guys are one of the best electrical help web-communities, so thanks for your time and efforts! I am advising some homeowners who need to rewire their first floor on Long Beach Island, NJ after ...
5
votes
3answers
2k views

Is it safe to install a three pronged wire into a four pronged dryer?

I just moved into an old home that has a three pronged wall jack as shown below: I have a newer dryer that has a four pronged wire. Please see the back of the dryer, I've removed the four pronged ...
115
votes
2answers
9k views

What is the purpose of these holes on my wire stripper?

I have been using this wire stripper for a while, but I have always wondered what was the purpose of those holes in the center and above LOOP, and those teeth on the handles.
4
votes
4answers
1k views

How can I fix chewed through wires?

I have two standard two prong wall plugs my puppy has chewed through completely, and he managed to sink his teeth into a laptop cord as well. I'm thinking the wall plugs are history (a lamp and a ...
2
votes
3answers
303 views

Inferring wire gauge from cable size

Is there any way to infer the gauge of the wires inside an NM cable from the size and shape of the cable? I reckon a round cable is generally -/3 W/G and a flatter cable -/2 W/G, but I do not know how ...
3
votes
3answers
6k views

is it possible to do a 3 way switch if power source is in the second switch?

In my research on how to install a 3 way switch, i've seen different ways on how to install the wires but i haven't found the schema that would help me in my situation. Here's a screenshot of my ...
5
votes
5answers
3k views

What's the suggested standard gauge wire for a given current?

I'd like to see a reference to an US or EU standard that lists in a table the suggested wire gauges for AC/DC and volts / amps.
4
votes
2answers
758 views

How do I connect a stranded wire to a bus bar?

A typical bus bar has this design: and connecting a solid wire to it is more or less easy. But how do I connect a stranded wire? I expect the following to happen: when I drive the screw in, the ...
5
votes
1answer
981 views

Can i run my cables from the outside box to the inside breaker box through 2x4 studs?

I am turning our carport into a living room and we have a 100amp breaker box outside that feeds power into the breaker box on the inside of our house. the conduit is going to be in the way of the wall ...
10
votes
3answers
8k views

Do I really have to fasten interior-wall electrical wire to a stud to keep it from moving?

I am fresh out of cable staples and would rather not go all the way to Lowe's just to get a box. What are the implications of not fastening loose electrical wires to a stud? It's not like there's ...
8
votes
1answer
2k views

Can I extend an electrical ground wire with a copper wire crimp?

I am working with an electrical socket and I need extra length on the ground wire. It doesn't seem unreasonable that I can attach an extra three inches to the existing one and attach it with a copper ...