3
votes
1answer
98 views

Is Schedule 80 PVC Conduit Suitable for Short Directional Boring?

I'm running some electrical wire around where I'm building my house. There are two places that I'd rather not dig through: A driveway and a creek. The creek is the most important, because the state ...
4
votes
4answers
639 views

How do I get all these wires up from the basement to the attic?

I'd like to run new cabling for data, voice and tv but I'm having a hard time figuring out how to get some of the wires up to the attic for the 2nd floor and would like some advice. I've run cables, ...
2
votes
2answers
502 views

Is a splice permitted in a PVC conduit body?

I'm talking about something like this Type LB Conduit Body
1
vote
3answers
523 views

Why would you use copper electrical conduit?

This is not "home" improvement per se, but it fits the spirit of this stack exchange. While waiting for my train I was peeking into a ceiling that had all of its slats removed for some kind of ...
5
votes
4answers
1k views

Why is it good practice to remove sheathing from NM wire when going through conduit?

I've been discussing specifics of an electrical job with a licensed electrician and he mentioned that in my area, it's acceptable/recommended to feed 12 gauge NM wire through an outdoor conduit but ...
4
votes
4answers
5k views

Can I use indoor Romex in buried outdoor conduit?

Or should I use outdoor Romex? I heard that outdoor Romex doesn't need conduit as you are just supposed to bury it. Edit: Ack, I should have mentioned I have existing conduit that I want to pull the ...
0
votes
1answer
124 views

Can the sheath of nonmetallic cable be removed prior to entering electrical metallic tubing (EMT)?

Can 2 romex cables be stripped before entering an EMT to allow more conductors in a 1/2" EMT? How would you transition from Romex to individual conductors going in or out of the EMT? Or is that ...
2
votes
1answer
214 views

How should I connect conduit in the wall to conduit on the ceiling?

In running conduit for a subpanel, I'm not sure how to make the transition from conduit running vertically in the wall cavity to running out from the wall along the ceiling. I could notch the top ...
1
vote
1answer
611 views

What are my options for running feeder cable into an exterior main panel?

I'm trying to connect a 4/3 nm feeder cable into to my exterior mounted service entry / main panel. There is already what looks like a 1 1/2" rigid conduit from the crawlspace through the rim joist ...
4
votes
3answers
224 views

What material to use to close a too wide wire tunnel?

During the cold days I noticed a little draft coming from the light switch next to my house door. Removing the switch revealed that the tunnel for the cables was widened to fit the cables for the ...
4
votes
2answers
384 views

Is there any NEC code requirement for how far off the floor Category 5 wiring must be run?

I am currently running conduit for Cat5e cable in the home office I am finishing off. Are there any rules in the code for how far off the floor Category 5 wires in conduit must be run?
7
votes
2answers
356 views

Do I need junction boxes where conduit containing data cables terminates?

I'm going to be running 1" blue PVC conduit from all my low voltage boxes to a structured wiring panel. My wiring panel will chase to the attic where necessary and I was wondering what the best ...
2
votes
2answers
2k views

How do I connect the wires inside a conduit junction box?

I have some wiring in my garage (done by a sparky believe it or not...) where the wire is quite loose, just tacked to the wall with clips, and there are a few junction boxes as well as the usual ...
2
votes
2answers
1k views

Should I be able to run some 1.5" PVC chase conduits from attic to basement next to a cold air return?

I have a new home I just moved in to and rather than having them put this stuff in ahead of time (silly me) I'm now trying to do it now. Here is my situation... I live in a 2 story home with a ...
1
vote
3answers
581 views

Should I be worried about this gap in electrical conduit?

Background My project this weekend is to get my garage repowered so my tenant will be able to plug his car in during the winter months. When I bought my house it was recently renovated by house ...
8
votes
3answers
5k views

Why is ENT rarely used for electrical wiring?

As best I can tell, the National Electrical Code 2011 allows electrical non-metallic tubing ("smurf tube" or ENT) to be used for running 120 V electrical wire. But everywhere I look, I see remarks to ...
9
votes
2answers
773 views

Can I use old abandoned iron pipe as electrical conduit?

I have an older house (1920) and I have been planning on doing some rewiring to get rid of some k + t stuff. Anyway, I just noticed today that there are some irons pipes that used to be part of the ...
7
votes
2answers
2k views

How do you protect romex at the end of an EMT run?

Sometimes you need to run a circuit through both protected & unprotected space. For example, you might put a recep in workshop (unfinished walls = unprotected) over a crawlspace (protected). To ...
5
votes
3answers
3k views

Does a grounding wire from a breaker panel to an outside grounding rod need to be in conduit?

I've got a breaker panel in my detached garage (it is not a sub-panel, but is a primary forked off just past the meter). The panel seems to be wired correctly- the neutral and ground bars are tied ...
5
votes
3answers
856 views

Running electric cables in basement shop

I am setting up a workshop in the unfinished area of my basement. I need to run a couple of electrical outlets and would like to run them along the block walls through grey PVC. Will this be a ...
3
votes
3answers
1k views

What's the correct way to pass wire to exterior electrical box?

I'm doing some remodeling in our basement, and came across the following (see pictures). It looks like the contractor simply wrapped tape around the conduit to secure the box to the wall. How are ...