0
votes
0answers
29 views

Why is my bathroom vent fan tripping the GFCI when being shut off?

I have a GFCI tripping when a vent fan is being shut off. I saw in KeithS's answer to a similar question that the blades rotating after shut off causes an imbalance, tripping the GFCI. In my case the ...
1
vote
2answers
43 views

Why use AFCI receptacles rather than AFCI breakers?

Is there any reason to use an AFCI receptacle rather than replacing the breaker with an AFCI type? It seems that providing protection on the whole circuit makes much more sense than to just one ...
0
votes
2answers
73 views

How do i know if my service panel will accommodate a 240v circuit breaker

We are looking to install a hot tub and trying to find out if our service panel will accommodate a 240v circuit breaker. This is what our panel says but I do not know what all of this means: ...
0
votes
1answer
44 views

Is 40-amp breaker enough for my new range?

My new range says it needs a 40-amp circuit breaker minimum. But it also says maximum draw is 13,200 watts on 120/240, so doesn't that mean a 40-amp breaker would be inadequate? By my math, max ...
1
vote
1answer
53 views

What to look at first when when circut breaker that fridge is on is tripping?

I have a house where the circuit breaker has tripped a few time over the last several days. It flipped one evening, we flipped it back and was ok for a couple days. We went away for the weekend and ...
3
votes
3answers
68 views

Why am I getting no power to the branch circuits with a new sub-panel?

My home had an ancient Zinsco sub-panel in which the breakers were grounding out and arcing to the panel. I've swapped it with a new Eaton 100 amp panel. I've re-installed all the breakers, and ...
2
votes
2answers
82 views

Curcuit breaker not accesible

My dryer stopped working and I found out that the circuit breaker (fuse) had burnt out. I measured the voltage in the socket and it's none. I live in an older house in USA and the cable is inside the ...
0
votes
1answer
81 views

Can you put a small breaker panel after a 30 amp breaker from main panel in the house?

Looking to run lights in my garage. If I put a 30 amp breaker in my main panel on a 10 wire to a small breaker panel in my garage, can I put 2-4 15 amp breakers out there for the lights? Likewise, ...
0
votes
1answer
77 views

What subpanel and number of circuit breakers should I install in a detached garage?

I no longer am dealing with my contractor. Long story. But he ran 2 10-3 wires out to my garage for power. I think he was planning on putting a 30 amp breaker on the panel in the house for each wire ...
3
votes
5answers
579 views

Using a 30-amp tandem circuit breaker for a 120/240v circuit?

I inherited a main panel box from a homeowner that wasn't always fond of meeting the required NEC codes. As such, there are some oddities in the panel. One such oddity is the fact that he installed ...
0
votes
0answers
75 views

What could be causing our air conditioner circuit breaker to keep tripping?

Our air conditioner circuit breaker marked "AC", is tripping frequently after the AC unit works for a while. Sometimes as long as an hour or more and, sometimes as short as few minutes. We were told ...
1
vote
2answers
88 views

Why do I have no power in two rooms after plugging something in?

I plugged something into an outlet, and heard a sort of a sizzle noise. Now I have no power in two rooms, but the breaker did not trip? Any ideas into what happened?
0
votes
2answers
80 views

Can I get 3 double pole breakers in my circuit breaker?

I am considering purchasing a inline water heater and having it installed (Eco 24). Before I do though I want to know for sure that it is possible to install with my current breaker box (the water ...
0
votes
1answer
93 views

replacing 20 amp breaker which is the test breaker

I need to replace the 20 amp circuit breaker on my cutler hammer 200 amp breaker box. this happens to be the TEST breaker. what is the difference in the test breaker and a any other breaker if I ...
0
votes
1answer
63 views

Which thermal circuit breaker should I buy?

I live in a small house in Argentina where we use 220 volts. I have a thermal circuit breaker that do squeak noises when the iron starts or the fridge starts. I adjusted the four screws of the breaker ...
0
votes
1answer
52 views

Repairing a circuit when the break is unknown and inaccesible.

Background: 100+ year old house with lots of really janky, messed up stuff. Some novice before me has been monkeying around, so don't assume that the current wiring is sane, safe, legal, modern etc. ...
0
votes
1answer
117 views

One of my breaker switches buzzes when I flip it on, should I replace it?

I recently installed a ceiling fan in a bedroom, and when the fan is active the electromagnet was a little louder than I was use to, but figured it may just be a cheap fan. However today when I went ...
1
vote
1answer
125 views

How Many Amps Is this breaker? [closed]

I am trying to figure out how many amps this box has. Top left breaker is 50amp and top right is 30amp. I want to put an xray machine on this that requires 100amps at its max. Do you think its ...
2
votes
1answer
60 views

How can I determine if there is any damage to the conductors of a circuit?

I recently went to replace a couple 3 way switches and, I am ashamed to admit, did not do my due diligence when wiring up. The new switches were a different style and the wiring configuration was ...
6
votes
1answer
2k views

Why did my electric range wiring burn out at the terminal block?

Turned on our 2 year old stove (Whirlpool Gold) and heard fizzing noises, then smelled electrical burning. Went downstairs and shut off the breaker (40 amp). That was the only way to get it to stop ...
1
vote
2answers
1k views

Wiring to split one circuit for ceiling lights in multiple rooms?

I would like to replace some Knob & Tube wiring in my attic. Currently, the ceiling lights in most of our rooms are all on a single circuit and are branched using many knob & tube soldered ...
-1
votes
1answer
107 views

How to identify circuit breaker to non-functioning built-in microwave oven?

I have a wall-mounted over-the-range microwave oven that is completely non-operational at the moment; from the user's point of view, it's as if it were unplugged, but it is. Unfortunately, access to ...
1
vote
2answers
80 views

Is it safe to replace a GFCI breaker with an arc fault breaker?

We recently had our electrical panel replaced/upgraded and I noticed that our GFCI breaker was replaced with an Arc Fault breaker. Is that safe? Are GFCI breakers obsolete now?
1
vote
1answer
53 views

Does this arc fault breaker manage one or two circuits?

I recently tested our breakers to see what was mapped to what. In the process of doing this, I noticed that our arc fault breaker is handling a LOT. Specifically: 4 bedrooms 2 bathrooms Family ...
2
votes
2answers
156 views

Did I damage the breaker by incorrectly wiring a generator?

During a power outage I attached my generator incorrectly (I have never done this before - I just was not paying attention). Anyway, I crossed the ground at the box with the black. When I turned on ...
8
votes
1answer
687 views

How can I determine circuit breaker requirements for an electric range?

I recently had a new range installed and when an electrician was visiting, he pointed out that the circuit was over capacity because the range was rated at 12.2KW at 240V. He said 12,200 W / 240 V = ...
0
votes
2answers
85 views

What is this single pole switch to empty ceiling box blows breaker when switched on

I would appreciate some help thinking through what are the possible problems in the following situation? A newly wired circuit from breaker box ( 20 amp 12 AWG wire) to front of the house (longest ...
4
votes
2answers
257 views

When replacing a circuit breaker in the service panel, how can I determine which neutral is associated with the hot wire?

In my service panel I would like to upgrade two standard circuit breakers with AFCI breakers. AFCI circuit breakers differ from standard circuit breakers in that you attach the hot an neutral to the ...
1
vote
1answer
306 views

Can I install two GFCI receptacles on a multiwire branch circuit?

I am wondering if I'm using a 10/3 teck cable to power two 20 amp GFCI receptacles for a temporary power situation, can I use two separate single pole 20 amp breakers at the panel for each receptacle. ...
1
vote
1answer
126 views

Why is one half of a subpanel not working?

I have 12/3 wire running out to my garage. I have a double 20 amp breaker in main box and a subpanel with two single 20 amp breakers in the garage with black to one breaker and red to the other. The ...
6
votes
1answer
197 views

Is it okay two breakers are controlling the same outlets and appliances?

To be specific, we recently had some electrical work done. The electrician added a second panel. He left without labeling anything. So today I've been testing outlets and switches trying to figure out ...
2
votes
3answers
277 views

Any problem with installing two identical circuit breakers in series?

Suppose I want to reduce risk of a circuit breaker malfunctioning and failing to disconnect a shorted circuit. What if I install two identical breakers sequentially (one after another) so that if one ...
0
votes
0answers
57 views

Terrarium electric board

[hope this isn't off topic for this board] I'm doing a DIY electric board for my terrarium: in case something goes wrong at least the whole electric circuit won't switch off. My current setup is a ...
3
votes
4answers
2k views

What is causing my circuit breaker to trip instantly and trip the next breaker too? Update - Video Added

One of my circuit breaker trips instantly. I try to reset it but it trips immediately and trips the breaker under it too. I can reset the break next to it and it is fine until I try to reset the ...
3
votes
3answers
686 views

What ampacity circuit breaker would I need for an 18 amp electric heater?

What ampacity circuit breaker would I need for an 18 amp electric heater? Here's a link to the model (IEP-4024), it's North American, 240 volts, 4000 watts, installing it outdoor.
1
vote
0answers
200 views

Why do I have a 3 wire/double pole breaker for kitchen receptacle?

I am switching my kitchen receptacle to a GFI; it has 3 wires. I'm pretty sure I have to break the bar between the two hot screws, thus making the top and bottom on a separate circuit. What is the ...
1
vote
4answers
921 views

What would cause an AFCI breaker to trip under no load?

I have an AFCI Breaker that trips with 0 load - nothing plugged in, no lights on. To test that power is getting to the room, I turn on the overhead CFL lights (very light load) and flip the breaker. ...
4
votes
3answers
778 views

Why did my circuit blow after replacing a switch?

I replaced an older switch yesterday on an existing line of recessed lights. There are five lights on the one switch. On the same breaker; but different switch, there are 7 more recessed lights (all ...
3
votes
3answers
2k views

Why did I lose power to half the house when the breakers did not trip?

Using a voltage detector I determined that three breakers in the panel are not conducting voltage, yet they are fully on (not tripped). Thinking they were bad, I replaced a double throw 15 amp and a ...
0
votes
2answers
3k views

Where in the breaker box should I terminate the neutral wire from my dryer circuit?

I am looking for an answer to something I am lost about, hopefully I can fins some help. I recently moved into a new home. The previous owners had a gas dryer and no outlets for an electric dryer. I ...
3
votes
1answer
297 views

What are my options to repair a broken tab on a bus bar?

My A/C went out this week. The problem was a broken tab on a bus bar with cut power to one phase of the 220v circuit. My HVAC guy was able to get me going again by swapping the A/C unit to the dryers ...
2
votes
0answers
138 views

How do I troubleshoot a newly installed non-working outlet?

I recently spent several frustrating hours trying to figure out why an outlet on a new branch circuit would not power a load even though there was proper polarity at the outlet, my non-contact voltage ...
7
votes
2answers
1k views

How can two different breakers both turn off the same circuit?

I have a 40 yr old home with circuit breakers. While looking for the breaker to turn off a circuit (I was replacing a light switch), I found that two breakers, on the same side of the bus, but ...
1
vote
3answers
259 views

How would I wire a thermal circuit breaker and switch together?

I want to wire a circuit breaker and switch to a GFCI and some other outlets. This is for power outlets on a work bench. Something like: I have this for a circuit breaker: and this for a switch: ...
1
vote
1answer
602 views

What could be causing a new 20 amp dedicated circuit supported by a GFCI breaker to trip?

I installed a dedicated 20amp circuit home run to support a single duplex outlet in a bathroom. The GFCI breaker is wired correctly. However, When I plug in a load such as a light a the breaker ...
3
votes
1answer
210 views

How difficult would it be to replace these fuses with circuit breakers?

I had a fuse blow last night. While the short-term plan is just to replace the fuse wire, in the longer term I'd like to switch them out for circuit breakers for the added safety but mostly for the ...
1
vote
1answer
901 views

Why is the circuit breaker for my furnace stuck in the off position?

The breaker for my furnace is stuck in the off position. We were away for the winter and had someone shut it off, and now the breaker won't turn on at all. We shut off the thermostat upstairs thinking ...
6
votes
1answer
25k views

Why is my air conditioner tripping the circuit breaker?

Our air conditioner recently stopped blowing out cold air. When I went to check on it, I noticed that the outside unit wasn't coming on. We had had problems with ants in the contacter in the past, ...
3
votes
2answers
295 views

Why does the breaker keep tripping on a circuit with two rooms' lights and a sewer pump?

I have a circuit-breaker that is connected to lights in two rooms, and to a sewer pump in the basement. I had the sewer cleaned out and the pump inspected, and no problems were detected. I then had ...
4
votes
3answers
2k views

Why does my circuit breaker trip with any small load, even after replacing the breaker?

I have a 20A 240V GFCI breaker in my main breaker box going to a conduit to another breaker box outside. All worked well last summer. Now, when I put any load (weed-eater, light, etc.) on an outlet ...