0
votes
1answer
33 views

How to mount a pull-up bar to drywall on resilient channels?

I'm trying to mount a pull up bar on a drywall. The wall is shared with another unit though,so there are resilient channels behind the wall, and so the studs are offset from the dry wall sheet. What's ...
0
votes
1answer
37 views

Which stud should I mount to if they are different widths?

I'm trying to mount a pull up bar to the studs behind my drywall. The studs are 16" apart, but seem to be of different widths. Specifically, I see a 3.5" stud, 3.5", 2", 2", 3.5". Are these just 2x4s ...
0
votes
0answers
29 views

What is the difference between a C stud with a dent on the back and one without?

What is the difference between a C stud with a dent on the back flange and one with a flat back?
2
votes
3answers
82 views

How do I know if I will drill into a hole in a wall that was already made?

I drilled 2 large holes for mounting a flat screen in the bedroom. One hole is in a wood stud and the other is a metal stud. I will be renting out our apartment and will be taking the TV down and ...
2
votes
2answers
122 views

What's the point of a thin (1/4" width) piece of wood set diagonally between two studs?

What's the point of a thin (1/4" width, ~2-3" wide) piece of wood set diagonally between two studs? I just took out a piece of drywall for some other work I'm doing, and between two studs, there's ...
1
vote
1answer
351 views

Can a condo interior room walls have steel studs that are paper thin?

I'm a bit puzzled about what's behind the drywall in my high rise condo built 3 years back. When drilling into an interior room wall supposedly where a stud should be(found by a stud detector and yes ...
1
vote
3answers
249 views

How to make paint stick to a stud screw?

Around my house, I have a places on my walls where the paint has fallen off of stud screws. They are not popped screws. Rather, they are still depressed into the wall, so I don't know how why this ...
0
votes
1answer
307 views

Small stud wall to sloping ceiling under stairs

We have an under-stairs toilet that we are replacing. The toilet was quite old, so the drain was 20cm from the wall. Apparently newer toilets require the drain to be pretty much flush with the wall, ...
0
votes
1answer
3k views

How do I mount my TV on my wall with poor stud location? [duplicate]

My wall studs are in an inconvenient space, I had a spot on the wall where I envisioned the TV to go, but the location of the studs would not have this tv be in the center of it, and there is other ...
2
votes
2answers
692 views

How can I hang my cupboard on a stud wall?

I have a storage cupboard in which I'd like to put some shelves. No problem with brick walls as normally I'd just have wooden battens on 3 sides, srewed directly into the wall with rawlplugs, then ...
4
votes
1answer
689 views

How much movement is normal after mounting a TV on partition wall?

I have a wall that's made of plasterboards mounted on metal studs. I have mounted two DVD cabinets (each 22kg) and an LCD TV (40kg). To mount all this, I installed 6mm thick MDF panels across 5 of ...
1
vote
1answer
311 views

How can I block off a doorway with studwork on a brick wall?

I'm blocking up a doorway in a brick wall. I've decided to block it up using a stud wall as that should be a bit easier than bricking it up. I know that the bricks are 11cm depth plus approx 2cm ...
4
votes
2answers
381 views

How do I locate studs in my wall?

First, I'm not the handiest of men, but can usually figure this sort of thing out. I just moved into an apartment in Manhattan and we're wanting to mount shelves, desks, and televisions to the wall to ...
2
votes
1answer
243 views

How can I hang a heavy mirrored bathroom cabinet?

I purchased a bathroom cabinet today that is 1200 mm wide, by 750 mm tall, and 150 mm deep. When I brought it home, I discovered it weighed nearly 40 kg (88 pound) empty. I was told that I could use ...
6
votes
1answer
318 views

How do I install an old work junction box around fire blocking?

I have an interior wall with a one-gang light switch; it contains a dual dimmer. I'm trying to change this to a single dimmer, and to add a new switch (to drive the other load) on the opposite side ...
3
votes
1answer
2k views

Can I hang a bathroom cabinet on a single stud and drywall anchors?

I have a 15-20lb wood bathroom cabinet (24 inches wide, few feet tall) and I'll be looking to load it up with heavy bathroom supplies. Problem is there is only one stud available. Do you think one ...
2
votes
3answers
16k views

How can I pass cables vertically through walls that contain fire blocking?

How can one pass (speaker) cables through walls from the floor to the ceiling. I am assuming that drilling a small hole at the top, dropping the cable I want to pass through and catching it at the ...
9
votes
1answer
310 views

Can I modify a load bearing triple stud?

I am installing a small safe in a wall and when I cut the opening in the drywall I noticed that the studs were in an unusual distribution. The stud on the right was normal but then there were multiple ...
5
votes
2answers
11k views

LCD TV mounting bracket does not “fit” the studs location in the drywall - how can I overcome that?

I would like to mount my 32" LCD TV to a wall using a swivelling bracket that I bought. The wall it needs to go to is plasterboard so I need to mount it on the studs. However, I've got a problem - the ...
17
votes
4answers
5k views

How do I find studs when stud finders won't work?

I was trying to hang my TV at my new place, on an interior wall (between living room and a bathroom). Using the stud finder on other walls worked fine, but on this wall I got some very strange ...