Questions pertaining to clothes dryers

learn more… | top users | synonyms

3
votes
1answer
62 views

What could have caused the burnt electronics smell in my Kenmore washer and dryer?

I have a Kenmore washer and dryer (both electric) in a separate laundry room. We came home yesterday after being out, only to find a HORRIBLE smell in the laundry room. At first I thought of ...
1
vote
1answer
59 views

What should I do about a stubborn screw on the middle of a dryer cord connection?

I am attaching a 3 prong dryer cord to a dryer. The middle connection is being stubborn. The screw gets to a certain point and is stuck. It will not tighten and the connection is very loose. Can I ...
2
votes
0answers
25 views

GE gas dryer noise - is this from motor?

Hi I'm trying to fix my 13 year old dryer. It's started to have squeaking noise but I was able to fix that by replacing the front and rear bearing. Now it's starting to have this noise and I think ...
1
vote
0answers
21 views

MayTag Legacy Series Top of Dryer Won't Open

I can not open the top of my Maytag Legacy Series Dryer. There is a screw on each side of the top of the dryer pinning it down to the base? What do I do now to get to the rest of the dryer since the ...
1
vote
0answers
75 views

Gas Dryer suddenly trips any GFCI Outlet immediately upon being plugged in, but works fine in non GFCI

I have a Maytag Centennial gas clothes dryer in my laundry room. It is connected to a non-gfci outlet which is downstream of another outlet with built in gfci. It has been connected like this and ...
1
vote
0answers
69 views

Clothes Dryer will not heat up

I have a Samsung clothes dryer that stopped heating up. Here's what I've tried so far: verified that the 30 amp breaker is working fine verified 120/240v at the relay verified 9ohms across the ...
1
vote
0answers
127 views

How do I replace foam seal on clothes dryer?

I was doing some unrelated work on my Frigidaire clothes dryer and noticed that the foam seal that is attached to the front panel and sits against the blower housing was bent on the bottom and burned ...
1
vote
0answers
104 views

Why does lint come into our bathroom when the dryer is running

Why does dryer lint come into my bathroom through the air vent? Is there a leak in the dryer vent pipe? We just got our dryer vent cleaned.
1
vote
0answers
39 views

Should I remove dryer support roller residue and how?

I have a front-loading electric Whirlpool dryer (LER4634PQ0) that's got a sagging drum, making it noisy and causing it to soil clothes. I first noticed it via brown marks on my clothes caused by a ...
1
vote
0answers
901 views

Would this buildup cause “dHE” error on an LG Tromm dryer?

Got the machine off craigslist. During the drying cycle it stops and shows the error. The user manual tells that with dHE error I should inspect the water supply, if the water supply is within spec, ...
0
votes
0answers
23 views

How to remove a Ge dryer front panel

I need to acess the gas valve so I can install a lp conversion kit. It appears the front panel must come off. I have looked at various repair sites, but no help. This a stackable 7 cf dryer. Model # ...
0
votes
0answers
50 views

Connecting dryer vent in new window

We just had some old windows replaced with glass block in the basement. The installers added a window with an attachment to vent the clothes dryer but, of course, it's different to the one in the old ...
0
votes
0answers
24 views

Can I avoid installing the water inlet if I don't use the steam cycles?

I have a dryer with steam cycles (Model # WGD49STBW), and I don't plan on using the steam cycles. Can I skip installing the hose to feed water to the unit? I'd like to know if there are any benefits ...
0
votes
0answers
68 views

Why Is My Dryer Vent Electrically Charged

I recently purchased a home built in the 1980s. When I went to hook up my 3-pronged dryer cord (with L), I noticed the outlet is the old 3-prong (all straight) typically used for ranges. I switched ...
0
votes
0answers
24 views

Dryer wont heat

I opened the back panel of the dryer and noticed that there was no continuity in the high limit thermostat. I suppose I need to change it. I then noticed that one half of the heating element was ...
0
votes
0answers
24 views

heating element for a dryer how to know if it is damaged

If the heating element metal plate between the (stacked) 5 roll coil element is cracked more than half way could that cause the thermal switch to burn out
0
votes
0answers
1k views

How do I stack a washer and dryer without a stacking kit?

I have a Samsung front-load washer and dryer that I want to stack. The original stacking kit (SK-2A) is no longer available, but looks like this: The replacement stacking kit (SK-3A or SK-5A) is ...
0
votes
0answers
80 views

Clothes Dryer electrical 240v between hot and netural, 0 between other hot and neutral

I had to move around my dryer to do some work in my laundry room. When I plugged it back in, it wouldn't turn on at all. None of the buttons would even make the lights come on. I unscrewed the end ...
0
votes
0answers
46 views

Dryer heating element not cycling on and off

Looking for advice on my dryer. 3 wks ago the dryer quit heating. Broken element. Replaced the element and everything worked great... For 2 wks. Next thing I know, it's not heating again. Found the ...
0
votes
0answers
112 views

Why won't my Kenmore gas dryer run/stay running?

I am having trouble getting my Kenmore Gas Dryer to run/stay running. The timer appears to be ticking away but the dryer won't start. For a while I could "fiddle" with the dial & get it to start ...