0
votes
1answer
41 views

What kind of thermometer do I use to check dryer temperature? Can same one be used to check stove temperature?

Is there a thermometer that can be used to check dryer temperature, and if so, what kind should be used? Should only a multimeter be used on the dryer's thermostat instead? I'm just wanting to ...
1
vote
0answers
37 views

How do I replace foam seal on clothes dryer?

I was doing some unrelated work on my Frigidaire clothes dryer and noticed that the foam seal that is attached to the front panel and sits against the blower housing was bent on the bottom and burned ...
0
votes
0answers
29 views

What is causing my LG Electronics WM3677HW to constantly push cold water into the drum during the dry cycle?

My WM3677HW washer/dryer combo recently stopped drying clothes; it leaves them completely soaked. I know the pump works because I disassembled the machine and replaced the pump as shown here: ...
0
votes
1answer
88 views

Opening the cabinet on a Maytag Centennial Dryer

I need to replace the drum support rollers on a Maytag Centennial MGDC700VW0 dryer, but first I just need to get the cabinet open. Anyone know how to do this? This dryer has a toe panel, which may ...
1
vote
0answers
37 views

Should I remove dryer support roller residue and how?

I have a front-loading electric Whirlpool dryer (LER4634PQ0) that's got a sagging drum, making it noisy and causing it to soil clothes. I first noticed it via brown marks on my clothes caused by a ...
0
votes
2answers
189 views

Should I repaint this dryer part?

on a combination washer/dryer, there's one metal part called the dryer duct, where water vapor right out of the drum is heated some more before going to cold water bath to condensate. That vapor ...
1
vote
0answers
261 views

Would this buildup cause “dHE” error on an LG Tromm dryer?

Got the machine off craigslist. During the drying cycle it stops and shows the error. The user manual tells that with dHE error I should inspect the water supply, if the water supply is within spec, ...
1
vote
1answer
58 views

What are these parts described by the service manual?

The service manual for a LG WM3677HW shows a very bad diagram... and I'm not very familiar with the parts to ID them. The image above tells me to probe 3 components, and if out of spec replace ...
1
vote
1answer
630 views

Can I safely bypass the door switch on my dryer?

The door switch on my dryer is broken (the rocker part of the switch just hangs loose) and the dryer won't start. I have the part number, but I won't be able to get one for several days. Is this ...
3
votes
1answer
151 views

Should I repair or replace a dryer heating element and housing connector?

I have a Samsung dryer that has a burnt out heating element. I purchased a new one and removed the old one from the dryer. I have no problem with any of this. My problem is that the element ...
5
votes
1answer
4k views

What is causing the SUPER loud noise from my dryer

I have a maytag gas dryer. It is about 20 years old. Model number DG7500 It sounds like an jet engine taking off. I've noticed that it starts off quiet than builds up to a very lour roar. I googled ...
0
votes
2answers
323 views

Help identify this electric clothes dryer part from an Asko T701 dryer?

I just replaced the drum rollers on my Asko T701 electric clothes dryer. As I was removing the front frame to access the rollers, this metal part fell out (the Sharpie is just there for scale): I ...
2
votes
1answer
2k views

OHM reading for dryer element? Bad thermal cutoff fuse indication of element overheating?

So I've read that I should get about 10-50 ohm reading on my dryer element. I do get a reading of around 10(jumps around alot) on my element, but this is with the multimeter set to 200(the lowest ...
3
votes
2answers
807 views

Why won't my gas dryer stay lit?

My Amana gas clothes dryer is not heating properly. The gas ignites when the dryer is first started, but after the gas turns off the igniter glows and then turns off, without relighting the gas. Many ...
7
votes
8answers
11k views

My dryer heating element broke in two: Can I just wrap the ends together?

I have a Whirlpool Estate dryer that recently quit drying. I narrowed the problem down to the heating element, then removed the element assembly and found a clean break in the coil at one end. A ...
2
votes
1answer
2k views

How can I access the lint duct assembly of a Maytag Centennial dryer?

We have a Maytag Centennial dryer (Model # MGDC700VW0) that has had its lint filter neglected too many times in-between runs. When the lint filter is over-full, pulling it out actually lets lint ...
1
vote
1answer
327 views

How can I open the front of my dryer?

Here is a site with exploded diagrams of the unit. If I need to oil the main bearing on the on the drum or one of the roller guide wheels of the drum, do I need to undo the back assembly, or can I ...
1
vote
1answer
819 views

How can I quiet down a clothes dryer?

Our clothes dryer is currently working; it gets up to and maintains heat, no shuddering, dries clothes, etc. However, it is louder than it used to be. It is an older unit (Whirlpool Dryer LER4624DQ0), ...