A tool used for creating holes in surfaces, such as for mounting objects on walls.

learn more… | top users | synonyms

11
votes
3answers
1k views

What type of cordless tool battery chemistry should I purchase?

I'm about to buy a cordless tool set in which the tools all operate off the same form-factor battery. The batteries come in several different chemistries and I'm wondering which type is better for ...
13
votes
4answers
53k views

How do you know when and where it is safe to drill into a wall?

Lots of home projects involve cutting or drilling through walls (everything from nails, screws, or hooks to mount things to cutting through drywall and drilling through studs to run wire). In ...
5
votes
4answers
2k views

How do I drill additional holes for adjustable-height shelving?

I have a set of cupboards with shelves that adjust in height, by means of moving pins that hold up the shelves to different holes: Unfortunately, for some reason, whoever made the cupboards didn't ...
2
votes
1answer
2k views

1/2“ Chuck on 3/8” Cordless Drill?

I need to use a step bit with a 1/2" shank. I only have drills with 3/8" chucks. Is the arbor size on most drills a standard which would enable me to just replace one of the 3/8" chucks with a 1/2" ...
18
votes
4answers
56k views

When pre-drilling for screws, how do you determine the correct bit diameter?

Suppose I want to pre-drill for, say, a 5/16 screw. How do I determine the correct drill bit diameter?
13
votes
11answers
24k views

What is the best technique for using a drill to insert screws?

It looks so easy on the DIY programs, but I battle to insert screws using my drill. The screwdriver bit keeps slipping out, and it damages the screw head. Is there a neat trick for this? Should I ...
9
votes
2answers
494 views

How can I drill to an exact depth with a hand drill?

I'm drilling holes in 4"x4"s in order to put magnets in them. The magnets are 1/8" deep and I'd like to install them to be flush with the surface of the wood. All I have is a Ryobi cordless drill and ...
5
votes
6answers
1k views

What's a good general purpose light-use drill?

I was wondering if anyone had any suggestions for a decent general purpose light use drill for around the home? It's not going to get a whole lot of use. When it does get used most of the time it'll ...
4
votes
1answer
201 views

How can I bore a hole through a framing member, without causing a lot of damage to the wall covering?

I am putting in a new thermostat. I cut a 1" hole in the wall at about eye level. I have an endoscopic camera and i see that at about 3 feet off the floor there is a wooden board that runs parallel to ...
4
votes
4answers
374 views

What sort of bit can I use to drill out a thin seized screw?

I have a piece of moulding on an appliance that is held on by a long, thin screw with a hex head. The screw is perhaps 5" long and perhaps 1/8" diameter (modestly heavier than a wire coat hanger). ...
2
votes
4answers
3k views

How to drill a hole in the wood without an electric drill?

During a travel in Laos, I need to drill some holes into a double-door's wood to install a locker. The wood is rather hard, and I don't have an electric drill (and can't find it). I only have 2 small ...
0
votes
2answers
81 views

What is/are the proper method and tools for drilling into masonry?

Related to this question, The blinds project has gone pretty smooth up until this point. It seems that some walls have plaster or masonry behind them. Probably not a big deal, but I've snapped a ...
0
votes
2answers
157 views

Can you get an “optionally cordless” or “hybrid” drill? [closed]

I'm looking to buy a new drill, but all of them seem to be corded or cordless. Are there drills that can either run cordless, or off the mains, depending on whether it's plugged in? It seems that ...