A tool used for creating holes in surfaces, such as for mounting objects on walls.

learn more… | top users | synonyms

3
votes
2answers
631 views

Should the hammer function “feel” different from normal drilling function on a hammer drill?

Just bought this hammer drill to drill in very hard concrete, which it was unable to do. What surprises me is that I feel absolutely no difference (vibration while holding it, sound it makes, drilling ...
0
votes
2answers
113 views

What is/are the proper method and tools for drilling into masonry?

Related to this question, The blinds project has gone pretty smooth up until this point. It seems that some walls have plaster or masonry behind them. Probably not a big deal, but I've snapped a ...
2
votes
1answer
939 views

Can rotary tool bits be used with a drill?

Can I use accessories like this Dremel 110 Piece Super Accessory Kit with a regular drill or impact driver? Are there any advantages of rotary tools over impact drivers? I would guess they might ...
2
votes
2answers
724 views

Can my rotary hammer act as a hammer drill?

The concrete around my window is incredibly hard, too hard for my non-hammer drill. Somebody at Homebase advised me to buy this rotary hammer, which comes with special bits of 6, 8 and 10mm. He said ...
2
votes
2answers
269 views

How can I fill a hole in masonry so I can redrill?

I am looking to install a folding clothesline that is bolted on the outer wall of the house. To do that I will need to drill several holes into the brick wall, but as I have never drilled anything in ...
3
votes
1answer
9k views

How can I mount a security camera on the outside of the house?

I'm tasked with mounting a security camera on the outside of the house and I'm not sure what would be the right way to do this. There are two basic problems: how to mount the thing and how to run the ...
0
votes
2answers
244 views

Can you get an “optionally cordless” or “hybrid” drill? [closed]

I'm looking to buy a new drill, but all of them seem to be corded or cordless. Are there drills that can either run cordless, or off the mains, depending on whether it's plugged in? It seems that ...
2
votes
0answers
2k views

Why can't I drill into studs more than 1 & 1/2 inches?

I am trying to mount a TV onto an "exterior" wall. I used the quotes because I guess technically it may not be exterior (I live in a townhouse with dividing walls between the houses). Anyway, I've ...
11
votes
2answers
1k views

How can I drill to an exact depth with a hand drill?

I'm drilling holes in 4"x4"s in order to put magnets in them. The magnets are 1/8" deep and I'd like to install them to be flush with the surface of the wood. All I have is a Ryobi cordless drill and ...
3
votes
1answer
323 views

When drilling a tiled wall, should I aim for the seams or avoid them?

I'm going to drill a couple of holes in a tiled wall in my bathroom. Is it best to drill through the seams or the tiles? Should I avoid vertical or horizontal seams, or does it really not matter? The ...
1
vote
2answers
143 views

Are SDS drills metric, standard or all the same?

Can I buy SDS drills (or à drill machine) in the USA and use it with an European bought machine (or drills)? Is the SDS "connection" the same in Europe as it is in the US? Sorry for the language, I ...
1
vote
1answer
635 views

How can I drill through concrete blocks to allow drainage from my backyard?

My back yard has a brick floor and is surrounded by a concrete block wall. In heavy rains, the yard pools with rain water. How do I go about cutting drain holes in the wall or floor?
1
vote
0answers
207 views

Live wire running through entire apartment wall?

I'm currently renting an apartment and my spouse and I want to hang a metal fixture above the wall where our bed is (in lieu of a headboard...for now at least). Where I want to hang it is 4 feet above ...
2
votes
2answers
2k views

Do I have the right tools for drilling granite?

What I'm doing: taking rounded granite stones and cutting the bottoms flat with an angle grinder and drilling 2-3" the other side for a flower, pen, etc. (3/8") What I'm using: Bosch multi purpose ...
4
votes
2answers
13k views

Can a non-professional drill holes in a granite countertop?

I recently bought an under-counter kegerator and need to have some holes drilled in the granite countertop for the tap. The template and mount has 1.75" hole in the center (to run the beer lines) and ...
1
vote
3answers
16k views

Can an ordinary power drill drill through steel?

It's my dad's drill and it's a Bosch. I'm not sure about the model no. etc because the box is missing together with the manual. He's been using it to drill holes in wood to install doors and also ...
0
votes
2answers
4k views

What is the correct method to determine the drill bit size from the measured threaded diameter?

I'm trying to decide the correct drill bit size for a hole I have to make to fit my thread. I measure the (major) diameter of the threaded section as 0.5325 inches. The threads are not supposed to ...
2
votes
1answer
2k views

Can I use shorter screws to mount my blinds?

I've bought a pair of blinds that came with 1 1/4 inch screws; I'm unable to drill deep enough into the frame to fit the screws, the screws are sticking about 1/8 of a inch out . I end up hitting ...
3
votes
1answer
3k views

How to drill a grommet hole through a desk?

I have a wall desk that hides away 2 power outlet on the wall. How do I drill a grommet hole that is wide enough to run cables through and cover it with plastic wire cover. What sort of tool do I ...
7
votes
4answers
3k views

Do I need a corded drill to mix thinset?

I've been looking at tearing out my fiberglass shower, installing Kerdi, and re-tiling the whole thing. During my research into this project, I've come across quite a few forums that have members ...
1
vote
2answers
590 views

How deep should I drill a pilot hole in concrete for a 2 inch screw?

For fixing a 2 inch screw on concrete wall, how should I drill for good strength and no damage to the wall. I tried a 2 inch screw and drilled for 1 1/2 inch and later tried to screw it into the hole. ...
8
votes
4answers
9k views

How do I know if my power drill needs to rotate clockwise or counter clockwise to drill forward?

This maybe a dumb question but I simply want to make sure I got it right because the manual seems to be defective. I already got one of my drill bits ruined. So, could anyone show me both pictures of ...
3
votes
2answers
5k views

Can I use a drywall anchor in a stud to hang a shower curtain rod?

I am hanging a curved shower curtain rod to replace a spring loaded/standard curtain rod. The rod came with drywall anchors (3 each side) and I started drilling the holes for the anchors. First hole, ...
1
vote
1answer
113 views

Does it matter how the chuck on a drill is set when it is stored?

When I put away my drill for storage, should I be concerned about whether the chuck is fully open, fully closed, or somewhere in between?
2
votes
3answers
1k views

Is there a way to drill a 1“-diameter hole through 1/8”-thick steel using a standard cordless power drill?

I am trying to reinforce a custom door I am building. Because it's made only of two layers of MDF, it is not as rigid as I want it to be and shows signs of bowing. Since it's going to be a ...
0
votes
1answer
10k views

How can I fill a hole in wood so that it can be redrilled? [duplicate]

The original strike plate for the deadbolt is mounted with 2 screws on top and 2 screws on bottom. I'm replacing the whole deadbolt and the new strike plate only has 1 screw on top and 1 screw on ...
9
votes
3answers
1k views

How can I drive a screw with an impact drill?

I bought a Bosch PSB 650 RE Impact Drill and I have some question about how to use it for driving screws. I know it's not its primary function but for a few screws here and there it should work. I ...
4
votes
1answer
244 views

How can I bore a hole through a framing member, without causing a lot of damage to the wall covering?

I am putting in a new thermostat. I cut a 1" hole in the wall at about eye level. I have an endoscopic camera and i see that at about 3 feet off the floor there is a wooden board that runs parallel to ...
4
votes
1answer
1k views

How to drill and waterproof a hole in cinder block for PVC drain?

I have a new electric hybrid water heater that emits condensation from a drain tube (normal) which is a bit different than a traditional electric water heater. Right now I have a bucket under the ...
3
votes
7answers
41k views

How do I remove a drill bit that is stuck due to an overtightened chuck?

I recently bought a Bosch PSB 500 RE power drill and already I kinda screwed up the machine. The chuck is keyless, consisting of two parts which I'll refer to as the head and the base. You would ...
2
votes
3answers
702 views

Should I purchase a hand driller?

Can I use hand drill machine, which runs manually not by electricity, to drill in plastic pipes, bottles, and cement walls? The purpose of purchasing it is to get hands-on experience with some DIY ...
5
votes
1answer
2k views

What units are the clutch settings on a drill?

I have tried looking around the internet for an answer - but I can only find articles that explain what the clutch on a drill does. I am very familiar not only with what they do but also with how ...
6
votes
6answers
15k views

How can I center a drill bit so that it drills absolutely straight down rather than perhaps a little off to the side?

In Googling "drill bit guide" came across this and other tools like it: Something like this seems perfect for being able to drill a straight hole through wood. However, I can't seem to find ...
1
vote
3answers
179 views

How can I secure a plastic toolbox to the wall?

I have a plastic toolbox that I want to mount on the wall. I need it to be extremely stable once mounted, and I was therefore considering simply screwing it directly to the wall. However, I'm ...
4
votes
3answers
1k views

Will neodymium magnets harm my power drill battery?

I glued some magnets onto my power drill battery to use for storing drill bits on - but will the magnets affect the battery life?
10
votes
1answer
5k views

What is the difference between a ball/pin detent and friction ring impact wrench?

I have been looking into getting an impact wrench for my car and I have noticed that any given model (at least the one I am looking at) has two versions. One version has a ball to keep the socket ...
10
votes
3answers
489 views

Should I get a keyed chuck for cordless drill?

I am thinking of getting a Milwaukee M18 fuel drill/ driver combo. The drill is insane with 750in-lbf of torque. It comes with a hand tighten chuck though. My other Milwaukee corded screwdriver has ...
16
votes
6answers
45k views

When would one use an impact driver versus a regular drill?

Or vice-versa. As best as I can tell, the impact driver is very good for most any type of screw going through wood. When would you use a drill (with screw bit) instead?
1
vote
0answers
33 views

How to replicate holes in a wooden cabinet? [duplicate]

Possible Duplicate: How do I drill additional holes for adjustable-height shelving? I would like to modify the vertical position of a shelf inside a wood cabinet. The dowel pins are glued ...
2
votes
2answers
2k views

How to drill a hole in brick with precision?

I have bought old cabinets which I would like to hang on a brick wall. I have marked the spots on the wall, but I find it very difficult to drill precisely, because the drill bit follows a path of ...
3
votes
4answers
4k views

How do I choose more durable screwdriver bits?

I recently bought a $35 cordless screwdriver that came in a suitcase with screwdriver bits. I was in shock when the Pozidriv bit splintered after screwing only 3 1-inch screws in the leg of an ...
2
votes
1answer
520 views

How to fit things to a Bungaroosh wall

The walls in my house are made of Bungaroosh which means that attaching anything to them is most likely to hit some issues. Recently I've been trying to fit a floating shelf to the wall, but no ...
-1
votes
2answers
193 views

Drilling a hole

I have a set of drill bits but no drill. I need to make a hole in a thin surface prone to splitting and don't have a hand drill or a power drill on hand ; what could I use to make that hole?
2
votes
1answer
532 views

How can I drill my wall if it contains flint?

I live in an old victorian house. Some of the walls seem to have pebbles inside then you get so far and there is flint, the drill won't go any further. Its a nightmare putting anything on the wall! ...
2
votes
4answers
1k views

Alternative equipment(s) to drill a few holes on a 0.5 cm plastic beside using a small drill

Are there other alternatives beside a small drill (shown below) to drill a few holes on a 0.5 cm plastic? (Looking for something that is inexpensive, save energy, portable and can drill a decent hole ...
3
votes
1answer
575 views

What exactly is magnetic drilling equipment?

What puzzles me is a term "magnetic" in the context of Magnetic Drilling Machines by Euroboor (for example).
8
votes
5answers
3k views

How can I install a recessed light container in an abnormally thick ceiling?

We are in the middle of our home remodeling and we have just noticed that our ceiling seems to be a bit thicker than what the maximum our recessed lights allow for. As shown within the picture link ...
0
votes
3answers
999 views

Does this Dewalt corded drill have multi-speeds?

I can't tell if this Dewalt drill has multiple speeds.
3
votes
4answers
2k views

How do I widen a hole in wood for flex tube?

I bought some 1" smurf tube so that I could run coax, ethernet, and speaker cable to various low voltage outlets in my house. I used a 1-1/4" speedbor bit to make a hole in the floor from my crawl ...
4
votes
1answer
1k views

What size screws and spacer should I use for installing shelves on tiles?

I need help confirming what size of screws, spacer and drillbit to use for installation of a shelf in my kitchen. Some specifics: shelf is 200 x 30 x 1.8cm (spruce). shelf brackets ask for 4mm ...