The tag has no usage guidance.

learn more… | top users | synonyms

16
votes
6answers
22k views

How can I fill a screw hole so it can be used again?

My dishwasher attaches to the cabinets on the side via a screw. This hole has become a little stripped, is there a way to fill it in and then screw in to it again? I can't change the location of ...
11
votes
5answers
7k views

How do I keep drawer knobs from loosening over time?

I see knobs like this on cabinets, dressers, and closet doors. They are held in place with a single wood screw. Very often they are loose. I guess when we grab them we often impart a slight twist. ...
10
votes
6answers
6k views

What is a good way to cat-proof (or child-proof) kitchen cabinets?

Our 6-month-old kitten has figured out how to reliably open kitchen cabinets at floor-level, by standing on his hind legs and grabbing the knob. What are some good ways to make it harder for him to ...
9
votes
3answers
3k views

Is there any way to fix a hinge pulled out of particle board cabinet door?

I hit my head on the open door cabinet over the sink, yet again, and slammed the door shut in anger. Adding insult to injury, the whole hinge pulled out of the particle board and took a big chunk of ...
8
votes
3answers
5k views

Dowel joints in plywood

I plan on replacing my kitchen cabinets later this summer. The old ones were home made by the previous owner and are oddly sized so I need to make my own out of plywood. Is it possible to put dowel ...
7
votes
3answers
706 views

Reinforcing a shelf supported only by pins

Our liquor cabinet has the usual row of holes drilled on either side for height-adjustable shelves, with typical shelf pins: I think the wood is MDF + veneer. It might be plywood. It's not holding ...
7
votes
4answers
13k views

How do I install cabinets on a floating hardwood floor?

We just purchased a bunch of cabinets for installation of a bar / kitchenette in the basement. There are 4 wall cabinets and four base cabinets. These are going to be installed on the existing ...
6
votes
4answers
5k views

How do I drill additional holes for adjustable-height shelving?

I have a set of cupboards with shelves that adjust in height, by means of moving pins that hold up the shelves to different holes: Unfortunately, for some reason, whoever made the cupboards didn't ...
6
votes
2answers
799 views

Building a Work Area in the Basement - Requesting Feedback

I am a new homeowner of about 2 months now. I have not done much in the way of home repair before now, but I do find that I am quite capable so far. My largest project so far was the re-tiling of my ...
6
votes
5answers
3k views

Should I install bracing behind drywall for upper cabinets?

I'm renovating our kitchen and we will be installing upper and lower cabinets. My question is, should I take the time to install a horizontal brace between the wall studs to make mounting the upper ...
6
votes
1answer
604 views

How do I repaint my kitchen cabinets?

I am doing my first home repainting and I'd like to ask a question. I need to repaint my kitchen cabinets. They are currently painted with a glossy ugly shade of green (don't ask). Moreover, it wasn'...
6
votes
1answer
4k views

How can I install drawer slides so that they line up and work properly?

I've got some drawer slides I want to use in some garage cabinets: How can I make sure I install them accurately so that the drawer fits nicely and lines up right where I want it? If someone could ...
5
votes
3answers
6k views

Can I bore my own hinge holes?

I'm scheming to reface my kitchen cabinets with sustainable lumber (looking for FSC certified or salvage) and trying to figure out what my options are. Our existing hinges aren't much different from ...
5
votes
4answers
1k views

How should I attach crown molding to cabinets with limited space?

I am putting up some crown molding on top of some existing cabinets, but I only have about 12 inches of clearance. In the past when I have done projects like this, I have used a finishing nailer or ...
5
votes
5answers
2k views

Are there any built in cabinet 'kits' available?

I am wanting to do cabinets between a wall and a fireplace. This would separate our living room from our dining room, so I want to build media cabinets (A/V equipment, DVD shelves, and a full ceiling ...
5
votes
3answers
331 views

Is it worth it to replace the stock blade of a miter saw?

I have heard that the stock blades that come with miter saws are "crap" and that you should replace the blade. I recently bought a normal consumer grade 10" miter saw (a Dewalt DW713) which I plan to ...
5
votes
4answers
18k views

How can plywood edges be finished to conceal the plies?

My cabinet doors are tired and have many coats of ugly paint. Rather than strip all the paint off, I'm considering just chucking the old doors and making new ones. I like the plain style of just a ...
5
votes
3answers
6k views

Should I be concerned about fridge/freezer airflow?

We just recently had the following counter/cabinet system put into our basement family room. After everything was done, I started to get concerned about airflow. The enclosure was built in such a ...
5
votes
1answer
19k views

How can I estimate the load capacity of a set of shelves?

I'm pricing and researching supplies for built-ins in my living room. The plan is cabinets on the bottom, a cubby for a TV and staggered shelves for several hundred HEAVY books above that. My ...
5
votes
2answers
1k views

How can I hide exposed countersunk screws in kitchen cabinets side panel?

How do I hide screws on the side of a kitchen cabinet wall that has slightly countersunk screws? I will be painting my cabinets black.
5
votes
2answers
376 views

Should anchors be used with screws going into framing?

I have just installed a bathroom vanity that came with screws and anchors. However, I just screwed the screws directly into the drywall, which has 2x4 framing positioned exactly where the screws go. ...
4
votes
11answers
15k views

Can I use a circular saw for precise cabinet making

I will be building some cabinet boxes and my table saw has a short span in the fence so I can't cut to final dimensions on it. I've made some cuts before using a saw board guide and a circular saw, ...
4
votes
6answers
10k views

How do I repair laminate damage on a kitchen cabinet?

We have a kitchen cabinet that we accidentally attached a calendar to using tape. When removing the tape the surface came right off with it. My question is how to best repair this damage? It ...
4
votes
4answers
867 views

How to determine if hardwoods are under cabinets?

I'm house shopping and some homes have built-ins or kitchen cabinets that I'd like to remove. I was wondering, first, is it possible to determine without taking the cabinets apart whether there are ...
4
votes
1answer
11k views

How to install Kitchen Cabinets on a Drywall?

I have 2 Kitchen cabinets, each 50 CM on 80 CM, they weigh about 10 KG (maybe more? not sure). I wanted to hang them on the wall but just discovered it's a drywall, and seems pretty thin. It is a ...
4
votes
2answers
1k views

What size of lumber should I use for the mounting rail for shelves and cabinets?

I recently scrounged some steel shelving that I'd like to hang in my garage. This used to be in an office, its for paperwork but will work great for some things in my garage. The mounting holes on ...
4
votes
3answers
2k views

My cabinets “stick”

It's hard to open / close a lot of the cabinets in my apartment. There was one where I was seriously worried I was going to pull the handle off, I had to pull so hard to open it. Could the problem ...
4
votes
2answers
5k views

How thick should a french cleat be?

I want to use a french cleat to hang some basic open cabinets in my garage. I've seen recommendations anywhere from 3/4 to 1 1/2 inches thick, but nobody seems to be talking about weight. Is there a ...
4
votes
2answers
88 views

Installing base cabinets - screwing to the wall and each other?

This weekend I'll be building a couple of base cabinets to replace some of the existing ones, which I assume are original to the house (circa 1960s). I consider myself handy but have never built ...
4
votes
3answers
26k views

How can I refresh the finish on my kitchen cabinets?

I am getting ready to put my house on the market and I would like to clean \ "restore" my kitchen cabinets. They are an oak cabinet that aren't painted, they are stained. I don't know exactly what ...
4
votes
1answer
7k views

Can I hang a bathroom cabinet on a single stud and drywall anchors?

I have a 15-20lb wood bathroom cabinet (24 inches wide, few feet tall) and I'll be looking to load it up with heavy bathroom supplies. Problem is there is only one stud available. Do you think one ...
4
votes
1answer
160 views

Which router would be more useful for kitchen cabinet work?

I will start my biggest project to date in a few months, and now I'm buying and studying the tools needed. Which router is most useful in cabinet making? A plunge router or a laminate trimmer? Both ...
4
votes
2answers
9k views

How can I paint kitchen cabinet hinges?

We have old, ugly kitchen cabinet hinges. I've read conflicting opinions online as to whether spray painting them is a good idea. How would you do it if you were going to go for it?
4
votes
1answer
260 views

Refastening a cabinet door

A cabinet door in my kitchen detached from the cabinet- the screws are about 1/2" long and weren't enough to hold the door in place. The screws are short to keep them from poking out the back side of ...
4
votes
2answers
9k views

Is my kitchen cabinet door beyond repair?

My cabinet door became damaged as my sister put all her weight on it to pull herself up :-) Repairing the door is very tricky as these cabinet doors are on the kitchen island and the particle board ...
4
votes
1answer
1k views

Will this 22“ drawer slide replace the slide mounted to my 18” drawer?

I have a kitchen cabinet with 18" drawers, with slides on the side. The internal depth of them is 23" as is the length of the part of the slide mounted to cabinet. The inside of my cabinet looks like ...
4
votes
2answers
953 views

How to I “set out” the holes for hinges?

I am thinking of building some cupboards with inset doors and solid sides (e.g not a face frame). Are there any “trick” to how I measure the location of the holes for the hinge screws and bore? I ...
4
votes
1answer
438 views

What do you call the rubber strip attached to cupboard door?

My bathroom has a white cabinet, where one of the doors has an adhesive rubber strip running down the inside of the door. This is so when both doors are closed, you cant see a big black gap in the ...
4
votes
3answers
3k views

Why do my kitchen cabinets' magnetic door catches keep breaking?

As per the title, my kitchen cabinets use those little magnetic door catch devices. Where there is a small plate on the door, and a housed magnet mounted to the frame of the cabinet to hold the door ...
3
votes
2answers
160 views

Identify part underneath chest

I am trying to find the name for the following part. This is underneath a chest that permits it to be moved effortlessly. I am trying to find this part to replace as they are pretty worn.
3
votes
1answer
971 views

How do I fix a warped kitchen cabinet?

The side wall of the cabinet is slightly warped after I used the high temperature self-clean feature on the oven. This cabinet has three large drawers in it and now they won't close. The wall of the ...
3
votes
2answers
85 views
+50

Is it OK to have an air conditioning vent above a kitchen cabinet?

We're getting proposals to add central air conditioning to our house. We currently have no ductwork so adding ducts and vents is part of the project. One possible duct location is on the ceiling over ...
3
votes
2answers
371 views

How do I install kitchen cabinets?

I am thinking of replacing all the cabinets in our kitchen. What is the process for installing kitchen cabinets? (Ie. best to start in corner, and work out? Top cabinets first?) Edit: We have two ...
3
votes
2answers
6k views

Why are my cabinets peeling and how do I fix it?

I have a new apartment, but I noticed that my kitchen cabinets are suffering from what I can only call, "peeling". Here's an image to illustrate: Why are my cabinets peeling? And, how do I fix this?...
3
votes
2answers
3k views

How to clean kitchen cabinets?

I just bought a house with some dirty (greasy, grimy, dusty, &c.) wooden kitchen cabinets. What is the best way to clean them? I've read that paint thinner works well, however, I am afraid that ...
3
votes
1answer
63 views

Identifying cabinet hinge

I'm renting this house and one of these hinges broke. 1.) Can I replace this hinge? 2.) If so, what's the model number/manufacturer?
3
votes
2answers
3k views

Can I remove one side frame of the cabinets above the refrigerator?

The space for the refrigerator is more narrow than I'd like. Both sides have a wall/panel extending from the cabinets above. The space is 33"w x 72"h. The new fridge would likely by 36"w x 70"h (...
3
votes
1answer
441 views

Kitchen Cabinets And Dry Wall Screws

I've got some kitchen cabinets that were hung using 4", course threaded, dry wall screwed. At every stud there is a screw at the top and bottom of the cabinet. Additionally, each cabinet is joined ...
3
votes
1answer
88 views

Will 1x4's and 1x6's be enough for an aquarium stand?

I'm building an aquarium stand, with only wood and screws. I'm only equipped with a miter saw, a drill, and some hand powered saws and a leveler- this will be my first woodworking project. The goal is ...
3
votes
3answers
3k views

How do I fix the shelf support holes in my cabinets?

In my pantry cabinet, the holes for the plastic brackets has gotten too large and they do not hold. The cabinets are made out of particle board. Does anyone have any suggestions?