Take the 2-minute tour ×
Home Improvement Stack Exchange is a question and answer site for contractors and serious DIYers. It's 100% free, no registration required.

I bought a house that had been sitting for some time. One of the the issues that I've discovered is that the flapper valve leaks. I've come to this conclusion by turning off the water to the tank and combing back later to see that the water level is lower.

I have already replaced the flapper valve itself, and the leak remains.

share|improve this question
    
Can you replace the rubber gasket the flapper valve seals against? It could be old and brittle which prevents a good seal when the valve closes down on it. –  ChrisP Dec 28 '10 at 0:58
    
Unfortunately, not easily (it will likely be easier to replace the tank). The previous owners had installed a low flow retrofit in the tank that while noble in cause makes it very difficult to work in the tank. –  MichaelT Dec 29 '10 at 3:02
add comment

5 Answers 5

up vote 3 down vote accepted

Over time the surface of the plastic part that joins the tank to the bowl can get tiny defects in it that prevent the flapper from making a good seal. As Jeff suggests, you could try cleaning that part, or just replace it.

share|improve this answer
add comment

Sometimes when a flapper gets old and begins to fail (disintegrate) it can leave a piece behind stuck to the outflow pipe that it covers. This piece/remnant then prevents the new flapper from getting a good seal. You might want to clean out the tank and make sure there are no remnants of the old flapper stuck in there.

share|improve this answer
    
There are no remnants of an old flapper on the valve seat - I have scrubbed the seat with an abrasive cleaning pad. –  MichaelT Dec 29 '10 at 3:08
add comment

I recently had two toilets begin to leak and had a hard time figuring out exactly where. I hate plumbing but decided to do full replacement of the various parts. I purchased two toilet repair kits for about $18-20 each. Instructions on the package explained what to do. When you are done all parts and gaskets that wear or deteriorate over time are replaced and you essentially have a new toilet. It's fairly easy but it does take some patience and careful work so you don't crack the toilet or tank during disassembly or reassembly. It's also a little messy since you have to get all the water out of the tank. I also replaced the line from the shut-off to the tank so everything is new. It took about an hour for each toilet but now I don't have to deal with something else needing to be replaced next year. Well worth the investment of time and money. And I felt good about doing something successful with plumbing. But I still hate plumbing.

share|improve this answer
add comment

You might consider replacing most of the insides of your toilet. A nice kit is Fluidmaster's S2DBL ($56 on Amazon or about $42 at Home Depot). I used this to replace a low-flow retrofit that a previous owner installed -- the flow was often insufficient.

The S2DBL kit includes a replacement ballcock, flush valve, task gasket, and bolts. Because it's a dual-flush kit you can configure it to use less water, without sacrificing the ability to do a full flush when you need it. If you haven't installed a kit like this before it will probably take 1.5-2 hours, but this kit has good visual instructions and Fluidmaster has excellent phone support if you need it.

share|improve this answer
    
After a few months, both my Fluidmaster dual flush kits started to leak. I replaced them with kits from Being Water, which have worked wonderfully since: beingwater.com/dual-flush-kits-and-accessories/… –  Shimon Rura Oct 25 '12 at 19:42
add comment

Home Depot sells a toilet flapper that comes with a new piece that the flapper rests on. The new piece isn't a replacement, but actually comes with a tube of silicone and seals on top of the old piece. I can't remember the name of the product, but you'll find it with the other toilet flappers for about $3 to $5.

I had this same problem and this particular flapper worked for me.

share|improve this answer
    
I'd post the link, but I'm having trouble finding what it's called. I think it may have been a Korky product. –  Jeremy White Jan 5 '11 at 0:19
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.