How do I make a height adjustable desk?

Question

Has anyone made their own height adjustable desk? I'm interested in making a computer desk that can easily be adjusted for either standing or sitting.

The lift mechanism could be electric or mechanical, as long as it is not too hard or time-consuming to adjust.

(There are commercial options around, but they start at $700 for the cheapest of the cheap. I'm sure I could make something myself for less that would better suit my needs.)

Update: Just to answer some of the questions in the comments. The desk would be supporting two 22" LCD monitors, a laptop, paper and anything I leave lying around the house long enough for her to throw on my desk. :-)

I do have access to some welding expertise.

Also, I live in Australia so importing from many of the places suggested would be impractical.

Answer 1

This is just my opinion, but I think you might be hard pressed to build one cheaper than you can buy one. If you're just looking for a project, it might be a challenging one. But if you're looking to save money building your own, I don't think you will.

If you own your own fabrication shop and have lots of scrap to use then this might be an interesting build, but for the average DIYer I would say it's cheaper to buy then to build in this case.

If I was going to build one I would probably use a Scissor Jack for inspiration.

Another idea would be to use electric Linear Actuators and a telescoping tube system in the legs to lift the top.

You could potentially use the pistons from some old office chairs, but you would have to make sure the desk top had enough weight to compress them (otherwise you would have to lean on the desk to make it go down). You would also have to physically lift the top to the desired height, which depending on the weight could potentially be a problem. You may also run into trouble engaging the lift/lower mechanism of all the pistons simultaneously.

I came across this product which in itself would not be a solution, but the mechanism for lifting it could potentially be adapted to suit your needs.

Answer 2

If you want to make a non-traditional desk you could have four posts fashioned together into a frame that goes high in the air. You could then "hang" the desk using an easily adjustable pulley system to raise or lower the desk. The surface could then be on a track system to keep it secure. There would be plenty of caveats but something like this could work if you put enough thought into the design.

Answer 3

Pricing it up it seemed cheaper to get a second pair of monitors and a video switch - then build a separate low and high desk with regular IKEA parts - and simply stand / sit in front of each

Answer 4

I've built this desk twice. It costs me ~$100 USD in materials:

And here is my version of the desk:

You can adjust it, but it is a little difficult. However, you can fit a modified treadmill under it as you can see in this video of me using the desk. I'm able to type comfortably while walking at 2.2 MPH.

If I may presume that the reason you want a height-adjustable desk is so you can sometimes sit and sometimes stand ( or walk!), then take the idea of height-adjustable and flip it on its head. Just buy a tall chair instead. (I only have a stool at the moment):

I have a height adjustable desk at work ( not ghetto'ized, like my home version). The linear actuators for my desk come from LINKAK:

Note: I came to this page because I want to make a new version of my desk electronically height adjustable. If anyone has specific ideas for my design, please be so kind as comment on this post. I'm not particularly mechanical, so I don't know all the pitfalls of different design decisions.

Answer 5

I bet you could eliminate a lot of the engineering and fabrication work in making something like this by making a desk that has only two positions, standing and sitting, vs. trying to make one that's continuously adjustable anywhere between its highest and lowest setting.

I'm thinking of something using a four-bar linkage on each end of the desk to keep the work surface flat while you move it from one position to the other, with pins to keep it secured in either position. You'd also want to incorporate some form of torque member to make sure the two linkages rotate together, to eliminate the need to always lift in the left-to-right center of the desk. Something like a closet rod might work for this. If you wanted, you could adjust your linkage geometry so that in the standing position the surface had a slight tilt, but was flat in the sitting position.

Of course you'd be limited in how much stuff you could put on the desk because you'd be moving it by hand and not by electricity. You could use a counterweight in your linkage to offset some of the weight.

Answer 6

I recommend Kim Stanley Robinson's Bibliography, fleshed out with some Frank Herbert, and a large solid hardback for the top; I'm using 'The Pythons' in the case, but gardening and DIY manuals are equally good candidates.

Fine tuning can be done with Asimov, Van Vogt, Niven, or Simak. You may be tempted to use Ian Livingstone and Steve Jackson, but they're not very good for this purpose as there is too little variation in size.

My setup is particularly quirky; due to my number pad I use the left of my keyboard more. With this in mind I've bolstered the left stack with Simon's Cat, The Bunny Suicides, and similar comedic hardbacks.

Answer 7

This is the finished project for my adjustable height live edge computer worktable: Finished Live Edge adjustable table

Answer 8

I'm a programmer and I currently use a drafting table as an adjustable standing desk. I wanted something that I could use in both sitting and standing position. The table I'm using is similar to the model shown here:

I can adjust the height by loosening the knobs and sliding the upper section upwards. The tabletop can be adjusted to be horizontal. This is working reasonably well and is a fairly cheap solution (actually, I found the table in a store room of our offices, but I have seen similar ones on the net selling for around $150)

There are some negatives, as it's obviously not designed for these purposes:

• The top end of the range of adjustability is slightly lower than I would like. I'm fairly short so it works out OK but it would not be high enough for a tall person. I have to use monitor risers on top of it to bring my monitor up to eye level, but the keyboard height is about right.

• It has a bit of a bounce to it when you are typing, if it is fully extended. I place a tripod under one of the front corners to stiffen it up when using it standing.

• It's somewhat cumbersome to raise and lower with monitors on top, though I have still been doing this an average of once a day. My co-workers usually look at me with a look of concern and imply that I'm going to injure myself. I get underneath and hold the tabletop up with my back to control the ascent/descent while holding both knobs with my hands.

Answer 9

Been thinking about this all day...came up with two ideas, both less than desk-like to keep the costs down.

1) Simple tabletop mounted to rails on the wall. Lots of options for mechanical lift (scissor jack was my first idea, but I'd probably play with something hydraulic for fun). The rails would work like they do on a shelving system. You'd have to keep all the weight on the back edge though, probably not safe-enough for my house.

2) If you're mostly doing computer stuff, mount a monitor to the wall on an arm and use an adjustable keyboard tray on a normal desk. I'm also thinking you could DIY the keyboard tray as a small-scale project before moving up.

Answer 10

I finally got around to actually building a real stand-up desk.

I ended up using metal stainless steel wire kitchen shelving...the kind you can get at Costco and the like. I didn't place any shelves between keyboard height and the top and used the keyboard height shelf as my actual desktop, then rigged a 'half shelf' above that to place my monitors on. I've since found that the wire shelf systems also have half-width shelves available for that type of task as well.

It's not adjustable in the sense that it raises and lowers whenever I want, but it's a really affordable stand up desk. As a bonus, it has wheels (easy to move) is steel (so can put notes everywhere with magnets) and is wire mesh (so it's easy to run all my cabling and zip-tie it all up).

My next goal is to find a height-adjustable stool that I can use on occasion when I do want a break from sitting.

Answer 11

I just did a quick search on shopping.google.com and came up with this. There were a number of hits on just legs. So I guess it all depends on aesthetics and what type you're looking for.

I think the biggest thing would be the ease of the ability to raise/lower the legs evenly when there's a load on them. The "push button" legs in the link above might be a bit tough, I.E. you push the button in and the leg shoots down because it's now free and there's a load on it and it pinches your finger or snaps down to the next level, not to mention you'd be raising one leg at a time and you'd have the added trouble of the load on the desk potentially being on a slope for a bit while you adjust the other legs.

Hydraulics with a locking mechanism (similar to a car hoist) would be a nice choice but you'll probably pay through the teeth for something like that and I'm not sure if they make something like that in a smaller size.

Answer 12

I looked at getting something like this extensively as I am now working from home. In the end, I decided I didn't have the time to make it myself and I didn't want to spend the money it would have required to get one of those kinds of desks that I actually liked. So I decided to go with a nice solid table I got off of Craigslist for $8 (think older table you'd see in a school - just a top with legs). Then I got an adjustable keyboard tray (from amazon, bout $115) and a nice chair (whew $600) and love this setup. Not exactly an answer to your question but maybe an alternative (plus I can leave comments yet).

Answer 13

I've been designing a desk priced around $150 that uses pulleys to raise/lower the surface (sitting at 28" and standing at 42") and a slotted forward leg to allow tilting of the surface if so desired. It is 63"x36"x92" this is my "forever desk". If there is interest I'll release some photos of it when it is done this weekend (hopefully).

Answer 14

Found this link to a build it yourself in wood article which might satisfy your needs... its more of a laptop table rather than taking your suggested two monitor config but might give you some ideas for a larger one...

http://woodgears.ca/laptop_table/build.html

Answer 15

Geekdesk.com does sell just the frame of their desk, which knocks a good bit off the price AND the shipping, possibly making that a good starting point for such a project. ergodepot.com does the same (with many more frame styles), but they are more expensive.