Tell me more ×
Home Improvement Stack Exchange is a question and answer site for contractors and serious DIYers. It's 100% free, no registration required.
up vote 2 down vote favorite

I'm seeing a new small hole on my hardwood floor since last week. It almost looks like it was a black spot before and then it became a hole. Is this because I didn't maintain the floor? or is it some sort of insect that did it?Black hold on hardwood floor

share|improve this question
Is there an indentation around the hole, or is the wood flat except for the hole? – BMitch♦ Aug 16 '12 at 1:01
1  
there is no indentation, the wood is flat except the hole. It almost looks like someone pushed a burning cigarette through it. – coder net Aug 16 '12 at 1:03

3 Answers

up vote 17 down vote accepted

It's likely a knot that came loose. The circular grain around it sure makes it look that way. The wood can turn blackish like this if water gets in there and sits which could easily have happened with a small hole like that.

share|improve this answer
1  
Agreed, sure looks like a knot to me. +1 – BMitch♦ Aug 16 '12 at 1:25
It could be water. I remember my wife used to put a wet umbrella in that area sometimes. How do I fix this? – coder net Aug 16 '12 at 1:40
1  
This is certainly a knot. The grain flows nicely around it, so there is no question. Water on the floor could have gotten in, causing the knot to swell, then pop loose. You can fill the hole as others have suggested. – woodchips Aug 16 '12 at 10:04
Yea- that panel should not have been placed there (not inspected prior to installation) it should have been used on the sides or not used at all. I would suggester removing it.. I know what a headache right? If I were to fill it I would not be proud of that. – ppumkin Aug 16 '12 at 11:46
3  
Pin knot. A twig was fully engulfed during growth and since the embedded growth collar got cut off in manufacture, the core no longer was structurally tied to its surroundings and was just waiting for the right humidity change to slide right out. – Fiasco Labs Aug 17 '12 at 2:48
up vote 3 down vote

Clean out the loose or soft darkened area with a utility knife.

Fill the hole with stainable wood filler that is close to the shade of the floor, such as this

wood filler

After it dries, if you need to color it to blend in, try one of these markers.

stain marker

If necessary, make it just barely darker than the surrounding wood. It will look like a small knot. The colors can be blended by putting small dots of diferent colors next to and over each other. Go slowly.

Seal it with a touch of polyurethane with the same sheen as the rest of the floor (it looks like a satin finish in the picture).

share|improve this answer
1  
Wood filler on a constantly moving floor? I do not think that is a good idea. The panel needs replacing. Its allot of work but it the best solution (and in the back of my mind I would have nightmares waiting for the wood filler to crack again.. arr) – ppumkin Aug 16 '12 at 11:43
1  
@ppumkin -Manufacturers use wood filler to patch small voids in engineered floor all the time. Modern fillers have a polymer base making them much more flexible than old water-based wood putties. The hole looks about 1/4 inch or so and seems to be wider underneath than on top, making for a captive plug. I think the risk is small, and the effort to remove a board in the middle of the floor and replace with a new one that is properly set in may be beyond the skill of many DIYers. If tackled by a very skilled craftsman, I agree that board replacement is a more permanent solution. – bib Aug 16 '12 at 12:37
Fair enough. I would not do it anyway. It would bug the hell out of me. And I would not do it for anybody else either. I suppose to cover it up if you were renting a house.. then who cares right? :-) – ppumkin Aug 16 '12 at 12:39
up vote 0 down vote

Black holes are caused by a massive body collapsing in on itself, creating a dense object with a gravitational field so strong that the escape velocity is greater than the speed of light. Or, a knot falls out.

I'd drill out the dark matter around the hole, and fill it with a dowel to about 1/8 below the floor surface. Then I'd do my best finishing the top with wood filler.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.