Take the 2-minute tour ×
Home Improvement Stack Exchange is a question and answer site for contractors and serious DIYers. It's 100% free, no registration required.

I saw this etsy project:

Working Arcade Light Switch

And while it's pretty cool, I'm not huge into arcade or fighting games, so I was going to make my own, and change the buttons.

How would be a good and easy way to do that?

I don't want to make my own switch, but rather, reuse an existing switch. I don't want to modify the internals of a switch, because I want to leave safety mechanisms in tact.

My first thought would be to use a "decorative" switch and replace or cover the button mechanism, but the biggest problem with that is that the switch sticks out too far to be easily covered by the wall plate. So, I'm thinking I want to recess the switch somehow, and I might be able to manage something by bending the metal part the screws screw into, but I'm not sure that's a good option, and feels quite hackish.

Any suggestions?


Update: I think that everyone misunderstands my request? I don't want to open up the light switch. I want to change the appearance of the system.

Thought experiment: Let's say I really like chocolate bars, so I want to make a chocolate bar light switch. I want to follow all the UL rules.

  1. Glue a plastic chocolate bar to a rocker light switch. I look at it from the front, and it looks great, covered the switch. but I look at it from the side, and I can still see the light switch, I don't like the look of it (because I want to hide the light switch).
  2. I measure the amount the chocolate bar sticks above the wall. Let's say that's 1 inch.
  3. I take a jig saw, and cut out all the sheet rock that would be covered by the chocolate bar.
  4. I remove the switch, electrical box, and move all in-wall wiring aside for the time being.
  5. I then remove 1 inch (or the amount discovered in step 2) of the stud the electrical box was attached to, everywhere that is now exposed by the sheet rock.
  6. I reattach the electrical box, now 1 inch more recessed than it was before (presume there's still room, because it's a big wall)
  7. Re attach the wiring, and put the switch back into the electrical box.

Voila, I now have a chocolate bar lightswitch, and it looks the way I want. Did I violate any UL rules? Or otherwise do anything an electrician would say is a bad idea? I don't think so. If so, please let me know which step is wrong. I could do all of this, but step 5 is an annoying step, (as is step 3). Can I avoid any of those steps and recess the light switch in another way?

share|improve this question
    
This whole project seems quite hackish regardless of how you position the underlying switch. :-) –  Kellenjb May 9 '12 at 21:34
1  
It might be helpful if you specified exactly what kind of buttons you want to have. –  Kevin Reid May 10 '12 at 0:43
    
I'm thinking I'm going to try to add PS2/PS3 controller buttons. –  McKay May 10 '12 at 15:44

3 Answers 3

If you really want to do this, you'll probably need to call an electrician and explore some low voltage controls for your lighting. Many wireless options exist, and you could conceivably make them look like an 80's arcade, or the engineering deck of a space ship.

What you have to remember is wiring devices must come with a UL rating. If you modify, use or install them in a manner that was not prescribed by the manufacturer, you immediately ruin that rating. That goes for high and low voltage systems, all must be approved.

Some, however require only momentary push button switches (like you'd find in arcade games) with a certain voltage / amperage rating.

Would anything bad happen if you found an unconventional way of mounting a decora rocker switch so everything lined up just right? Probably not. But I can't advise you that doing so would be a good idea.

share|improve this answer
    
I added an example to better explain what I'm looking for? Please help me understand how I'm violating UL ratings? –  McKay May 15 '12 at 5:06
    
Note, I didn't say violate :) You just void the rating by modifying the device in any way (that also goes for the rough in box currently housing the switch). If you bend the metal on the switch to install it, you void its rating. If you modify the box, you void the rating of the box. –  Tim Post May 15 '12 at 11:08
    
You can however cut the little ears off all four corners of the switch, it's designed to let you do that so it fits in certain types of enclosures (which is why they come pre-scored). Bending the metal tabs where the 6/32 screws hold it to the box violates the rating of the switch. –  Tim Post May 15 '12 at 11:10
    
So, do you believe that the original etsy switch also voids the UL rating? –  McKay May 15 '12 at 14:43
    
From the images given? Probably. Again, see the last part of my answer. I'm telling you (as an electrician from the US) that what you're doing would not pass an inspection if you in any way modify the switch, or the rough in box that holds it. –  Tim Post May 15 '12 at 15:14

Please do not try to modify an existing switch. This could prove dangerous and a fire hazard. Instead, consider using a flush style rocker switch such as a Pass & Seymore as shown in this link. http://www.legrand.us/dimmers-switches/light-switches.aspx#.T6uHJujPH0c They are available at Lowes and many other retailers.

share|improve this answer
    
Precisely, I don't want to modify the switch itself. I don't want to take it apart. I want to put other stuff in front of it to give it a new appearance. But if I do that, it makes it stick out an extra couple inches, which makes it look ugly. Thanks for the information about the flush-style switch, but that link didn't show anything in particular. –  McKay May 10 '12 at 15:43
    
Based on further research, I think the "flush style rocker switch" you recommend is the decorative switch I linked in my original question, and it still sticks out too far, I want something slimmer, or more recessed. –  McKay May 10 '12 at 16:41
    
I added an example to better explain what I'm looking for? –  McKay May 15 '12 at 5:06

I would not recommend this. Switches are tested to electrical safety standards which includes making sure they have adequate insulated properties that prevent you the user from getting a shock. They are also designed to drain a short circuit to the earth/ground by cross bonding metal components built inside the switch. Modifying a switch could invariably invalidate those safety features. Making it a hazard for you and anyone else using said switch.

share|improve this answer
    
That's exactly what crossed my mind when I read the question. –  Steven May 10 '12 at 1:38
    
Precisely, I don't want to modify the switch itself. I don't want to take it apart. I want to put other stuff in front of it to give it a new appearance. But if I do that, it makes it stick out an extra couple inches, which makes it look ugly. –  McKay May 10 '12 at 2:15
    
@McKay Also realize that by installing a UL listed wiring device other than how it was intended to be installed, you ruin the UL rating. Additionally, wiring devices must remain accessible. I am an electrician, I don't recommend doing it. –  Tim Post May 12 '12 at 14:23
    
I added an example, to better explain what I'm looking for? –  McKay May 15 '12 at 5:06

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.